Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
Hi,
Someone has been working with Alarm Cluster. I tried to implement it on multiprotocol dorr lock example but it was impossible. I have been reading ZCL library revision...
Hello,
I am trying to PCA10040 example project program to NRF52810 BLE module.
I just know that the 52810 has different(small) memory with respect to the 52832.
So,...
I have compiled ble_app_blinky sample code from nRF5_SDK_17.0.2_d674dde SDK and loaded it with s132_nrf52_7.2.0_softdevice.hex in my nrf52382 board. I can discover this device...
Hello,
I want to use a Li-Po battery with my nRF52833 development kit and I can't find the specific name of the J6 connector in the DK documentation. Does anyone know...
Hello ! I am working on the asset tracker project on NCS 1.4.0. Since I switched to this NCS, I have an error that comes up very often (once in two or once in three): get...
Online rajAsthana a few seconds ago in reply to Einar Thorsrud
Hi Einar,
Now I am able to put my board(nrf52840) in DFU mode with buttonless code using Esp32 as...
Hi,
I using nrf52832 evk board and sdk17(S132). I want to add the internal temperature sensor reading to the ble_app_buttonless_dfu_pca100400_s132 code present in the examples...
Hi,
1st time using nRF52840 - EV-BT840 on Keil V5.25.20
I use SDK 1702, reference to example examples\dfu\secure_bootloader\pca10056_s140_ble
My question is what softdevice...
Hey,
I have isnstalled ncs v1.3.1 and the toolchain specified in the instructions ofr 1.3.1.
I am trying to utlise the date-time library in the https_client example. ...
Hi Great Nordic Support Team:
Our clients are developing products with 『 nrf52840-WLCSP』. And they find out that there are some mis-information on the spec.
It's described...
Hi,
Dear nordic friend,I am trying to download NCS1.31 by using toolchain manager,but it work bad,show in below.
I have use some ways，to make me can visit the web in Europe...
Hi, I'm having difficulties driving SDOUT when it's configured to pin 19 on the NRF52840. I can operate the peripheral and see output data when my WS2812_PIN macro is assigned...
Hi all,
I am interfacing with a CAN Controller (MCP25625) that sets an Interrupt pin when data is ready (active low). That pin is then connected to a GPIO on the nRF9160...
Hello
I'm using a passive buzzer controlled by PWM. When PWM is set and run, the buzzer will continue to output small noises.
This is probably a code problem. Below is...
