I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
I'm developing for a custom board that has an nRF52832 and an FM25W04 external flash. My application uses nRF Connect SDK v2.9.2. I have a debug build that doesn't use a bootloader...
Gemini gave me some code to help get the phy when a connection is updated which does compile but there is an error warning in vs code. Here is the code:
here is the error...
We are evaluating the nrf54 series chips for a new product. We currently have a product that uses the nrf52 series and the distance measurement library. I see that the nrf54...
Hello,
I'm using nRF52840 with Softdevice S140 7.0.1 and SDK 16 for my BLE application in which I send data via notifications. I'm interested in tracking the hvn_tx_queue...
Hi everybody, I have some problems with flashing my custom PCB with an nRF52832. I saw online that you can flash the nRF52832 using the nRF52840 DK. I have looked into a lot...
Dear Support Team, I have downloaded the latest version of VS Code;
I have also installed the latest version of the nRF Connect for VS Code Extension Pack;
The J-Link...
ncs: v3.2.0
chip: nRF54L15
If I set CONFIG_PM_PARTITION_SIZE_MCUBOOT=0x10000 (64K), MCUboot fails to boot, and the error displayed is: 'Protect mcuboot flash failed...
We are not using the NRF5340DK board. According to tests, after initiating an SPI data exchange, the program is delayed in executing the next CS pull-high operation, resulting...
Hi,
I’m trying to finish the first exercise of lesson 1, but when I save it to flash and run the binary, I get this error and I don’t know what’s causing it.
Could someone...
Hello dear community!
Few months ago I bought a NRF52840 from MakerDiary ( https://wiki.makerdiary.com/nrf52840-mdk-usb-dongle/ ) for a personal project arounf Zigbee...
Hi Team,
I am using NCS v2.9.0 and trying to implement a custom Zigbee cluster with custom attributes.
Could you please suggest an example or guide me on how to send...
I'm currently testing the walkie-talkie mode on this development kit, however, when testing it outdoors it only allows a very short connection distance and disconnects. How...
Hi, this question might sound a little silly, but is downloading my device location history from nRF Cloud free of charges? I want to analyze my device's travelling pattern...
Hi there,
I am using an nRF9160DK and looking to get accurate Timing Advance numbers from it and also information on neighbouring cells. I believe in order to get an accurate...
We are using both serial ports running over USB on the nRF54L15DK:
uart20 is LOG, CONSOLE, etc.
uart30 is for our communication (enabled in our overlay)
When we...
