Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
Hello
how can i found a input capture example to read external 125KHz PWM Signal, so we can measure the time from falling/falling edge or rising/rising edge or falling/rising...
Hello, from reading devzone, the recommendation for optimal GPS performance while using the nRF9160 DK, is for the antenna to have an unobstructed view of the open sky.
...
Hello,
We have got some devices in the field that run mfw1.3.1 and an application that have some issues with preforming modem FOTA correctly. I'd like to update them to...
Hello,
I have been trying to provision and configure two nodes running Light and the Light_switch examples using a separate node running the mesh provisioner example from...
Hi,
I'm porting an older product that used a Microchip MRF24J40 SPI radio and a PIC processor to an nRF52840 and I'm struggling with how to replicate both the CRC calculations...
Hello,
I am using nRF Connect for VSCode (v2022.7.242) and discovered that the softreset option for a task has no effect.
Task:
Output:
As you can see it is...
Hi All!
I am using a hologram NB-IoT sim card in nrf9160DK. And want to connect it /send data to nrf cloud. I have activated the sim from the hologram website. When I tried...
I bought this device becouse I want to use it as Open Thread Border Router.
I followed the steps on your website: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
Hi All:
Good night!
We have 3 pcs of nrf52840-DK and would like to implement and test remote provision functionality with nrfsdk_17.0.2 and nrfsdk_mesh_5.0.
When compiling...
Hi，i'm use latest ncs sdk to develop bluetooth application which use Periodic advertising, when i get started with samples(bluetooth/periodic_adv), and use Ellisys capture...
Hello,
Is AT+COPS manual selection mandatory or just a preference? We have an issue with 9160 choosing a network without PSM if it has better signal quality (when roaming...
Trying to flash devices and getting this error:
make flash
DONE nrf52840_xxaa Flashing: _build/nrf52840_xxaa.hex nrfjprog -f nrf52 --program _build/nrf52840_xxaa.hex ...
Hi,
In our old project we developed low energy sensors based on the Nrf52811 (nrf Connect sdk), using advertisements to broadcast the sensor data, then collecting them with...
Hi
I use the nRF connect SDK v2.0 installed with the toolchain manager and tried the distance measurement which works fine but doesn't use the high precision mode. I changed...
hello Nordic
i am working with zephyr NCS(1.7.1) , with vs code (on manjaro) with the nRF connect extension.
i am looking for a way to map my include files, to find dependencies...
