Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Hi,
I have working with Bootloader development on nrf52840 controller, for that i followed devacedemy course for firmware update using Uart and able to update firmware using...
Hi,
I get a Mcu Mgr Error: 10 Group: 1, when I
start OTA on Android smart phone
interrupt during upload by disabling BLE on the phone
enable BLE again
retry OTA...
Hello,
I was using VS Code earlier today creating different build configurations for our hardware (nrf52840 and nrf9160 based) and everything was fine. I restarted the application...
I am currently using two nRF52840s to create a transmitter, one that acquires data and transmits it as advertisement data, and a receiver that receives data from the advertisement...
We are using nRF52833 with Softdevice S113 for BLE.
in the OS_Idle function, nrf_pwr_mgmt_run is called.
But never comes out of sleep.
Is there a need to call nrf_drv_power_sleepevt_init...
Good morning,
I am developing a RAK4631 (Nordic nRF52840 + Semtech LoRa SX1262) and now I need to manage the power consumption. My environment today is a VSCode/PlatformIO...
i am working with nrf52840 with nrf5-sdk 17.1.0 and with segger embedded studio 5.42a i am having trouble build a project and it is giving below warnings: Building 'main_app...
Hi,
I am trying to test the ICM42670 sensor using nRF9160 with Zephyr V2.6.0 and I am getting an errors when I init the sensor:
unexpected RESET_DONE_INT value, 0
ICM42670...
I’m using the nRF52832 with SDK 14.2.0 and would like to implement AES-128 CCM. Could you provide relevant documentation or instructions on how to achieve this?
I was developing my development kit with onboard sensors and other ICs. So, I was looking into NRF52 DK schematics and documentation. the problem is that the interface/debugger...
Hi,
I want to use the onboard 5340-DK QPSI flash for saving binary data into, however when i enable the support for it i get that the device is not ready. I have tried both...
The above is my code.
This is running log.
After scanning multiple times, my application may freeze, as shown in the log, and there will be no response after receiving...
I am developing a project on nRF9161.
I am interested in calculating data usage for different protocols (for example MQTT with TLS) when communicating with a server over...
Hi,
I refer to the method of the link below, which can generate factory_data.hex
https://docs.nordicsemi.com/bundle/ncs-latest/page/matter/nrfconnect_factory_data_configuration...
