I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hii,
I´m working with LTE IoT 4 Click, by Mikroe, that use a nrf9160.
I need to connect to network with my modem, but i have some erros. My goal is to communicate with...
...On a NRF5340, using NRF Connect 2.6.1 SDK and tool chain.
In our application, we need to select if NRF5340 device boots in ZIGBEE ROUTER role or ZIGBEE END DEVICE role...
I've written a custom manufacturing programming tool for ARM Cortex-M4 nRF52832 and nRF52810 devices. It uses a J-Link Plus USB programmer (J-Link V7.98g) and is implemented...
I am working with Zephyr RTOS and I would to prepare one of my RAK4631 with a Zephyr bootloader.
I know that in the RAK4631 documentation we have instructions how to flash...
Hello,
By using nRF Connect SDK v2.6.1, I want to have RTC (Date Time, Calender, etc) functions, so I modified the code based on one of Nordic Academy examples, which can...
Hi,
I've resumed working on my project with the nRF Connect SDK after a brief break. However, when I try to run a simple project, I occasionally encounter an error while...
Hello, I've recently purchased an npm1100-EK schematic from Digikey. The evaluation board works great but I can't find the Schematic & hardware files for this particular version...
Hi everyone. I'm using nRF Connect SDK 2.6.1. I'm implementing LittleFS for file management on an external QSPI-Flash. I need to format the flash and erase all of data. I...
Hello,
I am currently researching the best way to be able to change the rate at which I fetch a GPS fix. I want to start the program at 60 seconds, then depending on environmental...
This is a continuation of this question . It may be necessary reading to understand the context.
I 'm confused by this topic too, however I think the error about "boot_partition...
Hi,
I'm trying to build the MQTT sample for a custom board, trying to communicate between nrf52840 and nrf7002 via QSPI. Here's my board definition:
In the build configuration...
Hello everyone,
I Have a LTE reconnection issue after LTE signal loss with SDK 1.3.6. I was doing some LTE connectivity tests by placing the board in a faraday box. After...
Hello! We have developed a custom board featuring an nRF9160 and an ESP32-C3-MINI-1 co-processor, which is flashed with AT-firmware (version 3.2.0.0). Our current application...
Good morning, if I wanted to develop a board with the VM3011 device, where can I find it? It seems impossible to find it as a device in major stores, and I can't even find...
