Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi
I'm currently in the middle of porting our board from nrf sdk 2.6.1 to nrf sdk 3.2.1. I made it so far, that the correct dts are used, but somehow the build process seems...
I am following the instructions as per Getting Started with the Asset Tracker Template.
I have successfully created the environment and done the West Update.
When I do...
Hei,
I have nRF9151 SMA DK v0.9.0 running with board controller FW v1.1.0. This is stated by the Board Configurator v1.1.2 tool.
I tried to set both nPM VOUT2 and VDD...
Hello,
For my project I am interested in performing IQ sampling in the payload of a BLE packet, using nRF52833 at both receiver and transmitter.
I am manually configuring...
Hi,
We've been developing a product using nRF52840, where it does a lot of advertising and scanning.
We've migrated from SDK v2.5.2 to v2.8.0, and recently discovered...
nRF Connect SDK v3.2.1 on Windows 11
I am trying to build the Matter Light Bulb sample using a nRF7002DK but run it over Thread instead of WiFi (the default). Since this...
Good day,
When using the bt_gatt_discover() with a NULL UUID parameter, the code sweeps all UUIDs available from the start_handle to the end_handle. This is verified with...
Development environment: MacOS Sequoia (15.4.1), Visual Studio Code v1.108 0, nrfConnect 2026.1.1242
I am trying to develop a "workspace" project with a nRF52840DK as my...
I understand that the rf path should be 50 ohm coplaner to the output matching network that should be placed very close the the NRF chip. The recommendation shown in the reference...
I’m facing a Power Profiler Kit II (PPK2) measurement discrepancy that appears to depend on the host PC , not the target board or firmware.
Target setup
Custom board...
Hi all,
What is the increase in current consumption or power consumption when measuring RSSI with the nRF52833?
My device is a peripheral. I would like to estimate this...
I am using nrfx_nvmc_page_partial_erase_init() and nrfx_nvmc_page_partial_erase_continue() to erase flash in-between wireless connection events. The datasheet states: " The...
I have an IoT project that reads data from a proprietary device via an I2c SBIffer. The device consists of a controller and a small display, which are connected via an I2C...
I am referring to the ncs\v3.1.0\nrf\samples\bluetooth\throughput\sysbuild\ipc_radio\prj.conf for the nRF5340 and extrapolating that to a central application with multiple...
Hello, I hope this question is allowed here. I have received this email, after having been active on this forum:
Hi Mads, I saw you on the Nordic forum and wanted to get...
