Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi, I am currently using the PPK2 for current measurements.
According to the datasheet, the PPK2 supports a maximum source voltage of 5 volts. However, my device requires...
Hello
we are certifiying our product by ISO 13849-1 which includes the Nordic nRF52832, among more information I would like to start with the following questions
1. where...
Dear nordic support
We're in the concept phase of a product that implements cellular cloud connectivity.
We already implemented a "blueprint" ESW which provides supporting...
Hi,
I am planning to create an ultrasonic library (based on ch201) because I can't find any library for it. So I am porting code from ch201 development kit to nrf52 custom...
Hi there,
I have a Thingy:91 board and I would like to enable the accelerometer data to be sent to nRF cloud when using the Asset tracker v2 application. I saw that it is...
Good afternoon,
I'm trying to understand how the RTC works on the nRF52.
The RTC can run when HFCLK is OFF and PCLK16M is not available
Section 25.5 describes the TICK...
It appears that KConfig is uable to find any compilers for native_posix with VS Code on windows 10 after installing all recommended packages and prerequisites during SDK install...
Hello,
I am using LwM2M library in my project and I want to check what version I am using of LwM2M carrier library. Please correct me if I am wrong, is according to below...
I am creating software for a proof-of-concept device using the nRF52840 Dev Kit and nRF Connect for VS Code.
I started a few weeks ago with the Nordic UART Service code...
With Zephyr, I am using BLE Stack sample (rpc-host) on net core and peripheral_uart on app core. I changed the uart pins on from the standard dvk configuration on devicetree...
Hi
I was wondering why there there seems to be no information about profiling of the LC3 codec by T2.
Only information I found is from Karl's answer here :
The rule...
Hi~ I have a new NRF52832 REV3 xxAA board, and I need to read its SRAM value. However, when I use the JLink command to read it, I get 0. I have tried recover and eraseall...
I have the occasional issue where connecting VDD to VTG either on P20 or shorting SB24 will cause the nRF9160 DK to brown out. This happens when an external device to be programmed...
Good day everyone
I'm attempting to build a temperature sensor on i2c am running into this error. Currently using a custom board. I see that the issue was previously mentioned...
