Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi,
I am trying to DFU OTA by using nrfutil with nRF52840 dongle.
I have already write nRF connect desktop Bluetooth into dongle, but when I use nrfutil to do DFU...
I am using: nRF52840 nRF Connect 1.9.1 VS Code W5500 for ethernet Azure IoT Hub
I have the above (mostly) working. My code is based on the Azure IoT Hub sample for the 9160...
We are developing a device where we would like to include the bluetooth connectivity of the device with phone, to answer the calls and to listen to audio. We are using nrf5340...
Hi,
actually we have following Solution:
- NO battery powered devices - the first nrf58240 acts as a beacon advertsing temperature values all 10sec - On our gateway, there...
Hi,
I'm trying to follow the MCUBoot + SMP SVR example on this page: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/samples/subsys/mgmt/mcumgr/smp_svr...
My application uses NVS to store data and it works just fine - no errors reading or writing , and saved data persists between device power cycles.
My application also has...
Hi,
i have two nRF52833 program for make AOA. One is programe as Tx with "direction_finding_connectionless_tx" and one is program as receiver with "direction_finding_connectionless_rx...
Dear Support Team，
1. How to use Bluetooth Low Energy CGM service on NCS? Are there any examples for us to refer to? For example, nRF5_SDK_17.1.0_ddde560\examples\ble_peripheral...
I turn on the device, the led turns green. And I use usb to connect it with computer then I open the nrf connect for desktop, the bluetooth low energy tool,
10:51:05.822...
Hi,
Our custom board using the nRF52840 with SDK 15.0.0 experiences a higher current draw if it starts up without the USBD module enabled at some time. The first screenshot...
Hi, I work with SES on an nrf52840 on a custom board. Here is my issue :
My board can be wakeup from SYSTEM OFF with 2 interrupts on 2 differents GPIOs : 1 is connected...
hello Nordic
sorry to nag but i am waiting for an answer on the thread below for more then a week now, hope you can attend to it or at list inform that you are working...
Hello Devzone,
Working on my Ubuntu 20.04 LTS host, I recently lost ability to flash my nRF9160dk board. The embedded J-Link is detected by its serial number, but an attempt...
