Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
I am using NCS 2.9.0 and latest extensions for VS Code.
To reproduce, use Mac, create a new app from Blinky sample, build it and open "prj.conf", then wait a few minutes...
Has anyone else had problems with adding build configurations for workspace applications using the VSCode GUI interface? Initially I clone the repo using CLI-based west commands...
Hello,
I am fairly new to the development with nRF and am having problems getting sensor data from a connected BMP280 to the nRF5340 audio dk.
The first thing I did...
The nrfx pwm supports a number of events for a callback: /** @brief PWM driver event type. */ typedef enum { NRFX_PWM_EVT_FINISHED, ///< Sequence playback finished. NRFX_PWM_EVT_END_SEQ0...
Hey so I just wanted to use the BMI270 on the Thingy:53 and Polling the acceleration values seems to be working just fine. I wanted to use the DATA_READY Trigger. I am working...
Hi everyone,
I'm currently following the "WiFi Fundamentals" course provided by Nordic, and I'm encountering issues with this specific exercise (l5_e2):
To ensure I wasn...
In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
My application requires mathematical calculation based on double and float. For this I have included <math.h> in the header files.
FYI : I am using NCS 2.2.0
Also included...
Hi, I want to update an existing image in slot 1 with a new image in slot 2.
Both are flashed on the device and in my image 1 I want to initiate the DFU process, as mentioned...
I am currently evaluating the Thingy:91X and nRF9151 DK platforms for development using the latest NCS releases (v2.7.0, v2.9.0, and v3.0.0). I have encountered two issues...
I'm adding CONFIG_NET_CORE_MONITOR in both application and network config per https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/libraries/others/network_core_monitor...
Hello,
We are using Raspberry Pi + NRF52840 as Borderrouter for Openthread using Radio Coprocessor design.
However we are facing stability issues on the RCP where it...
I have an app running the S132 softdevice, doing most of the applicatino work in a routine being called by an 8 Hz app-timer. Under certain conditions that I detect with external...
