Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hello,
I am encountering difficulties connecting to and recovering my nRF52840 board with J-Link on macOS, both via nRF Connect and using nrfjprog in the terminal. Below...
Hello,
We are using the nRF52840 dongle (PCA10059) with the CLI agent software as a Zigbee network coordinator, and the Digi's XBEE S2C as a Router.
We are using XCTU...
Hi Team,
I have nRF5340 DK board and I want to test the Bluetooth Periodic Advertising with Response and Bluetooth Periodic Advertising with Responses Synchronization...
Hi,
I am trying to create a new custom service in nRF Connect for desktop and play around with its characteristic properties.
I Use an nRF52840 DK as peripheral and my...
Hi,
Its maybe a stupid question but is there a easy way to operate the DK with 3V VDD and IO Voltage? The 9160 DK had a simple switch for this. The default for the 9151...
Hi everybody I'm using nRF Connect SDK 2.6.1. Before I could seen Partitions section in Memory Report tool, but now it's disappeared. I also checked it by ninja command: ...
Hello,
I have a few questions: 1. How to add a prj.conf or an overlay file to enable peripherals to use an external high-frequency crystal oscillator as the clock source...
We have developed a firmware application using the OpenThread library for the nRF52840, utilizing the Nordic Development Kit and Segger Embedded Studio for ARM (version 5...
Dear nordic support team,
after having migrated my project to SDK release 2.8.0, the following message appears in the logs:
<dbg> bt_sdc_hci_driver: configure_memory_usage...
"I'm working with nRF Connect SDK v2.2.0 for nrf52840 and I'm trying to implement file transfer functionality using mcumgr over UART in Application. I've successfully configured...
Hi , I flash periodic_sync_conn sample to A and B development boards, and periodic_adv_conn sample to C development board. Only A and C development boards work normally, but...
Hello. We are developing custom boards with the configuration of nrf5340 + nrf7002.
In the previous sta example, a build error occurs when the "Board Target" in "build configuration...
I have customed my own nrf54L15 board and it would run on button battery. I managed to measure the battery level through ADC, but I don't know how to use ADC with nrf54L15...
I've been working for months to try and figure out exactly how to get my application to bond the way I want it to.
I'm using nrf connect sdk 2.4.2 on an nrf52832. I used...
