Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
I’m trying to set up a simple relay using an nRF52840 board to route data between a BLE central (my phone) and a 9600bps UART device. My goal is to send data from the phone...
i've captured the following using a joulescope js-220 as an inline current meter across the VDDM CURRENT MEASURE jumper on my rRF54-DK board....
i'm running the system_off...
Hi!
I'm storing a key in the KMU for use by the ECB.
If I set the slot's destination address to an address in RAM, the KMU pushes the key there correctly, but if I instead...
Hi,
I have a custom board, i enable the adc peripheral, and it generates:
then i connect the AIN4 channel and it generates:
but when i build i get the following...
Hi, I'm looking to develop an out-of-tree driver for the SIM800L modem. The reason I want to develop it out of tree is that I don't believe have the skills or resources to...
HI
I previously disabled DCDC in the app using the following method:
in app.overlay
I am using ncs 2.9.0 I saw some posts using CONFIG_ENABLE_DC_DC=n , but I am unable...
Hi,
I'm try to set up a UDP server on a nRF9151dk, and send data from a remote pc to the devkit. I have tested my sim and networking works correctly, I am able to use coap_client...
Hi,
I am using the nPM1100 in my new application, where the system power circuit includes two additional 250mA LDOs configured to provide a 3.3V output . I am also using...
Hi,
I am encountering the following build error with the BLE peripheral example after migrating from NCS 2.7.0 to 2.9.0 and when CONFIG_BT_LL_SW_SPLIT=y is set in prj.conf...
Hi,
I am using nrf Connected SDK v2.6.2 on windows 10. I try to create a blank application project for the device ADXL363 on SPI2 bus on the nRF9160DK board.
I basically...
hi:
I use ncs 2.8.0 ,nrf9151 dk and v2.8.0\nrf\samples\net\https_client.
I modified the DigiCertGlobalG2.pem
this is log:
connect() failed, err: 111.
What is the...
Hello,
I was wondering if there was a way to implement a physical on/off switch to the npm1300 that would allow the outputs to be isolated form the battery but still having...
We have designed a vehicle tracker that uses the NRF9160. We have found in the past that sometimes after the radio has been running for a while it gets into a loop where it...
Hi,
I try to develop a Bluetooth speaker using the nRF 5340 DK since i do not have a separate audio Dk for this. I am using the sample code Audio unicast client for this...
Hi
I have a project developed on the nrf52840dk / nrf52840 dongle and am trying to build it for the Laird BL654 dongle. The build fails due to a missing 'runners.yaml' file...
