Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
I have a JDY-16 BLE chip in AT command mode and are able to scan for a SoftRF device that has a Nordic UART service.
I can succesfully see the SoftRF device during a scan...
Hi All,
Currently I'm editing an example project using the NRF5 SDK in SES -- however, I'm not sure exactly how to best version a project or even export it to contain...
Hi,
For my nRF52840 custom board, when I send data through app_usbd_cdc_acm_write() to the serial port from main.c , data are transferred without problem but
when I try...
Hello,
I just recently updated to Windows 11 and facing the issue(nrfutil is not working) after win11 update. Previously, It is worked on Win10. Do you have the working...
Hi.
nRF52-DK board use. (PCA10040)
* now system : bootloader + softdevice + Beacon application ->> working fine. good.
* new system : Swtiching ESB or Beacon
I would...
When I connected mqtt on nRF9160, I found a strange problem, which caused the device to freeze and become bricked. The location cause was found to appear in err = mqtt_connect...
Hello, we are semi-experienced with Nordic,
We are doing a DC power driver, during operation we do a NUS data send if we are connected and the NUS has started. When we get...
Hello,
I am trying to optimize GPS power consumption, and the fix time. The GPS search period is approximately 10 minutes, modem fw 1.3.1 and nRF SDK 1.7.0. We are also...
Hi Nordic，
is the encryption technology used in the software protocol or hardware inside 52833?
our customer want to know the if the encryption can export,thank you！
I baught new DK. Form last few days, I was testing sample programs for learning purpose. Suddenly, SDK stopped being detcected via USB port ? I could not diagnose the reason...
Hi
I want to increase the number of leds in DTS file of peripheral-uart sample by using overlay file.
Is it possible to manipulate the aliases in DTS file by editing the...
I'm running in to the issue mentioned in the tile; " Only spi nodes accepted in /soc/spi@40023000/". I'm using nRF connect and built a driver for the TI ADS1291 analog front...
Hi, I read a couple of post that asked about the accuracy / tolerance of the internal REF, and the answers mention it's included in the gain error.
This made me wondering...
Hi,
as stated in the title, we have a nrf52840 dongle (PCA10059) which does not come up normally on a Nvidia xavier devboard. Output of dmesg:
We tried different OS...
Hi,
I'm working on an LwM2M client that reads three sensors in sequence every N minutes and notifies the server about the value change.
The server supports the LwM2M 1...
