Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hello,
I am developing an NFC application using the nRF Connect SDK v2.6.0 and the nRF Toolchain v2.7.0. During development, I tested my application on the nRF52840 DevKit...
I have MCU boot running successfully in my project using NCS 2.8.0 and sysbuild. I'm now trying to add hardware downgrade protection as described here:
https://docs.nordicsemi...
Continue.
PCA100059,S140,custermize periphral Blinky.
I have changed the value transfered between peripheral & center with
uint8_t* data;
uint16_t dataLen;
The max...
Hi,
I'm trying to use device_credentials_installer.py with an FTDI USB-UART cable, but the script returns "No device found." I've tested other scripts and confirmed communication...
Hello everyone,
I'm pretty new with BLE configurations. I'm currently implementing a BLE NUS service, and noticed that on the example code the max length supported is...
Hi Nordic Team and Other,
We are evaluating an audio product using a NRF5340 Audio Dk (Custom Board) and using nrf5340 DK for flashing the custom board using the setup as...
Hi,
We have a pcap file of a MQTTS connection to AWS, provided by the Soracom SIM console. I will print the first lines of the Wireshark trace so you can see what I am working...
Hi, We are evaluating whether nr54L15 supports LE Audio function? According to the specification, it supports bluetooth 6.0 and should support LE Audio (Isochronous channel...
Hi,
currently I am struggeling to get my SD card connected to the 54H20 DK. Each time I try to mount the SD Card I get the following error:
The Error is raised after the...
We are using a custom board design. I created a custom board configuration when using the v2.5 SDK. In this configuration, we have the UART0 pins configured such that RXD...
Hello,
I am using the nRF54L15-DK development kit. The peripheral-uart example works well to stream data from the kit to a smartphone using the nRF-tools App. However...
Hi
I want to use the timer in counter mode (gpio event shortcut to count task). Do you have any number of current consumption? The plan is to have a 64Hz signal but it could...
Hi, after uploading a Zephyr project (like the "Hello World" example), I couldn't see the device in the serial monitor. i add the below commend in overlay file also but still...
Hello,
I am in the process of following a series of tutorial videos on driving an LED with pwm, but I don't understand how to properly configure my .overlay file and my...
