Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
Hello, I’ve been trying to install Nordic Connect SDK 3.1.0 in VS Code, but the installation keeps getting stuck midway and never completes.
I’ve tried several times over...
I'm bringing up a custom board, working through the peripherals one at a time. Unfortunately, I haven't gotten very far before things started misbehaving. One part of the...
With mfw 2.0.2, AT%RAI supports now also "2 – Activate with unsolicited notifications."
That's verfy useful, but I miss some details in the documentation about the usage...
Hello community,
I am working on a project that requires the integration of the u-blox NINA-B302 module , which is based on the nRF52840 SoC .
I have previous experience...
Hi All,
I have been trying to create new custom board. and havent been able to even build.
I followed the intructions here :
https://academy.nordicsemi.com/courses...
HI,
We are producing products using the nRF52832. During production, a defect occurred where the lpcomp detection voltage was operating at a voltage lower than the design...
HI
I'm using nRF54L15-PDK 0.8.1. When debugging with VS Code, the debug session failed for some unknown reason. Afterwards, the PDK's nPM1300 output, which was originally...
HI
We are mass producing products using nRF52832.
However, during production, a PCB was found to not detect low battery voltage for about 5%, so we are inquiring about...
As the title suggests, we are having issues with BT notifications being throttled.
The function which does the notifications is below:
We loop over sectors of flash memory...
I am trying to replace such a platform and was hoping to use nRF9151 as a starting point.
Is such a platform possible at all with Nordic/Zephyr ?
I have an old 9160 dev...
I am trying to use Edge Impulse ML models on my custom board. I have built my model on EI and downloaded it locally. I followed the sample wrapper code to use my own model...
Hi, I am devolping a sensor system where I am in need of a Tri state GPIO solution
Currently using the NRF54l15DK with all the latest software versions (3.11, etc.), developing...
I am trying trilateration for indoor positioning system with nrf54l15 , using 3 initiators and a reflector I was not able to switch between initiators and also one of the...
Product is a zigbee router.
Use nrf connect sdk 2.4, update it is not an option.
The zigbee join work fine most of zb3.0 coordinator, BUT with an old coordinator it failed...
Hi all,
I'm using aws iot lib and last will topic feature, everuthing works but I have a question, in prj.conf I set my topic with
Is it possible to build this last...
