Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
I have created custom characteristics by
BT_GATT_SERVICE_DEFINE ( vnd_svc ,
BT_GATT_PRIMARY_SERVICE (& vnd_uuid ),
BT_GATT_CHARACTERISTIC (& vnd_enc_uuid . uuid ,...
I am using the current nrf-sdk v2.1.0, which includes the matter version v2.1.0 from the Nordic repository.
I encountered an error that setting CONFIG_DEBUG will result...
Hi
I have successfully used the TIMER & GPIOTE to generate dual tone frequencies for a BFSK project. 200kHz & 400kHz. ( 50% duty cycle square wave)
I wonder if the same...
Hi,nordic
I am using 52832. The SDK is mesh500 and sdk1710. I want to check the data sent from the PC through the serial port. Where am I and how do I read the data?
I am using the NRF52 development kit and I modified the uart example main.c to simple TX and RX application using printf function. The board is directly connected to the PC...
Good morning,
I ended up changing the design to use the nRF52810 chipset and I wanted to find out if Nordic would be able to provide some schematic feedback for my design...
Hi Nordic expert,
We are K5DET1/3/5/7/9/11 output high level, then string 10K resistor, K5DET2/4/6/8/10/12 through the mercury switch to read this high level, while adding...
Hi,
According to the documents of NCS, CoAP Server sample uses native OT CoAP API while CoAP Client sample uses Zephyr CoAP API, and the Zephyr CoAP API is recommanded....
I've googled all over, and I'm having a hard time finding any documentation that digs into how to use the nRF Connect SDK. Most documents point to examples, however the wealth...
Hi，
I developed with ncs 2.1 samples esb ptx and prx using nrf52840 make a low latency application，There are two problems
①On the ptx side, packets are sent twice in...
Hi, in our project we have to send some raw data to one node to other node using zigbee. So i have checked every single example but it doesnt match with what i need. I have...
Hi,
I'm trying to write a simple python application on Windows 7 that communicates with a BLE peripheral running Nordic UART Service. I'm using the nRF dongle and pyserial...
Hi,
I'm trying to config my SAM-M8Q with an array of HEX.
It's work beautifully with app_uart_put like the picture below.
However, when I try to implement LIBUARTE...
Hii
I have a problem pass the address while advertising
I should pass the adress using 9160_dk
However, in main.c there is this line:
#define DEVICE_NAME "Nordic_UART...
Hi there, I'm trying to find a hardware integration guide that details min max specs for the IC and also details the RF output pin impedance so I can match to my board stackup...
