Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hello,
I'm getting this error when trying to connect, which seems to happen after the first SMP Timeout. Most of the time connecting/disconnecting works, deleting bonds...
Hello,
We have been working on a Bluetooth Mesh application based on NCSv2.5.1 using nrf52840DKs for quite some time. We are now considering acquiring some DKs of the new...
Hello. The problems with starting advertising started after I wanted to add NVS (most likely). The error occurs in the bt_le_adv_start function
What does this error mean...
I am working on a project with the nRF9151 chip. In this chip, I am using the LTE modem in eDRX mode .
Apart from eDRX mode , I also want to put the MCU into sleep mode...
Hi,
I want to use the nRF53 with the timesync demo ( https://github.com/nordic-auko/nRF5-ble-timesync-demo ) to start an I2S task when a timer overflows on the net core...
Hello, The DevAcademy fundamentals lesson 6, example 1 shows how to connect a bme280 to a DK. Then in lesson 6, example 2 it shows how to connect to an onboard light sensor...
Dear Sirs,
I am writing you to inquire about following questions about nRF5340. Especially,regarding the configurable bitrate for the LC3 codec in nRF Connect SDK Ver2.8...
Hi
in my application, I need to reduce /disable RAM sections in nRF54L15 to save Idle RAM current. For Example, I need to retain only 64KB RAM when I am in idle.
how can...
Hi folks,
I'm attempting to program an nRF52833 using a Segger J-Link+ connected to the SWD program/debug pins on the board.The board is only an nRF52833 - as a learning...
hi, noted a few things in the Rev 1 Errata v0.8 that might be tricky to solve practically in sw/hw
3.16 [33] RADIO: GPIOs can exhibit radiated emissions
max...
I'm currently attempting to register a service and it's subsequent characteristics statically using variables and not hard coded GATT tabel , I can successfully register an...
Hello,
I've been playing with an nRF54L15 PDK, specifically with the sid_end_device sample. I was having a lot of trouble getting the device to register/connect to Sidewalk...
Dear,
We have project using normal advertisement (not extended) on a nrf5340 module (Raytac MDBT53-1M) to send data using Manufacturer data.
We have a product already...
Hi, Currently Im developing on a custom board that has a NRF52840 and a NRF9160. Both MCUs communicate using UART Async API and I added the support for LPUART on both sides...
