Hi Team,
Is it possible to implement the iOS application to track the iBeacon Component after closing the application(Background processing).
Please provide any example...
Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
Hello, I have a question regarding the watchdog with secureboot.
I just added watchdog to my app, but I'm worried that when I DFU the HW watchdog will trigger during the...
Hi,
I have tried to look through the forums but I cannot find exactly how the nRF Connect -> Power Profiler application is able to get/obtain the device SN?
In the log...
Hello, we have a project with nRF5340 and SDK v2.6.0, and we can not obtain the logs from the network core b0n bootloader , but we do receive properly all the other logs....
SDK:17.1.0 application: ble_app_uart(+ble_app_buttonless dfu service) bootloader:secure bootloader pca10040e_s112_ble Background: There is only one key(pin:31) on the PCBA...
Hi there, I am trying to use shell with the USB and logging with RTT. Additionally, UART0 async is used to communicate with sensors. Here a snapshot of the proj,config:
...
I'm developing a custom board with a uBlox NORA-B121 module, which contains an nRF5340. The board has a Microchip MCP2515 CAN controller, and for some reason, I can't receive...
I am porting an application from NCS v2.3.0 -> NCS v2.4.0. My application runs in nrf5340dk_nrf5340_cpuapp_ns with NSIB and mcuboot. The mcuboot uses external flash for the...
I have Thingy:91 dev board. I have flashed hci_lpuart sample to nrf52840 and successfully ran lte_ble_gateway sample. Now in my application I want to connect to the same hard...
Hello,
I'm trying to reduce the power conception of my custom board with a nrf52840 and a 4g modem on uart.
For this test, I reduce the code to a loop (modem is off...
NRF52840 running 17.1 SDK and using QSPI interface to erase a block of memory from AT25FF321A external flash IC.
When we call erase it takes 930 millisec to finish erasing...
I was able to turn ON the Nordic’s BLE DFU over SMP + BLE NUS using Matter Lock sample code successfully.
The “DFU over SMP” is really great but further customization is...
Our app uses the nRF5340. We use CONFIG_BT_CTLR_TX_PWR_DYNAMIC_CONTROL so that we can change the tx power for advertisements and connections. When using ncs 2.6.0 it seems...
Hello,
I am creating this Post to summarize all my findings regarding a problem with the SLM Application that multiple people are experiencing, in order to make it easier...
Hello,
We are trying to use the nrf5340 as a wireless HID mouse over BLE. Our cursor moves just fine on Windows 10, Windows 11, a Mac, and two Android tablets (Lenovo, Amazon...
Hello,
I'm using Zephyr 2.6.1 and nRF5340.
Tried to include in my project the NRFX driver for USB and I'm currently not able to find an enabling option for that.
In...
