hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Hello all,
I use nRF52840 for my custom board. I set P1.11 & P1.12 as UART_RX & UART_TX. But these two pins can not work.
Here is my nrf52840dk_nrf52840.overlay.
Here...
In the Wi-Fi throughput sample code folder the main.c file has virtually nothing in it, just a few boilerplate lines and a main() with only two lines of code that set the...
Hi,
I have a nRF9160-DK (PCA10090, 1.0.0, 2020.50) that I am trying to flash with the Modem Shell using the Quick Start app on a M1 Max MacBook Pro, running macOS 14.5....
Hey guys, I'm trying to set the max tx power for our nRF52840 project and I'm getting this error:
CONFIG_BT_CTLR_TX_PWR_MINUS_1 was assigned the value y, but got the value...
I'm presenting an issue when exporting the data collected with the Power Profiler Kit 2 in the software (nRF Connect for Desktop v5.0.0), specifically the digital outputs...
Good afternoon,
I am debugging the nRF9160 in a product, and what we are noticing is that the socket "poll" events do not appear to be generated when the system is in...
If you look at the circuit of the PCA10040, it uses a 32Mhz 12pF crystal.
C1 and C2 of the crystal are 12 pF.
However, you say to use this formula: C1 = C_L * 2 - 4pF...
I am attempting to store a pre-generated key in the psa key store using the psa API. I have taken the nrf->samples->crypto->hmac and nrf->samples->crypto->persistent_key_usage...
Hi,
I am working on a setup where nRF5340 uses W5500 Ethernet IC and communicate MQTT over TLS. The actual setup for now is nrf5340dk + w5500 ethernet shield.
I am working...
We found one charging issue on nPM1100, after we assemble the battery to the PCBA, and then apply 5V to nPM110 (VBUS) and GND. The protection ciruit does not release, and...
Hi,
I am using nrf52840 and SDK-16.0. Our product is already in the market.
we added some extra features now. after adding this we are not getting application timer call...
Hi,
I need to provide a clock signal of 4.9152 MHz to an external ADC.
Can the NORA-B106 module (that integrate a nRF5340) supply that signal by the Application Core M33...
I am looking to program the nRF52840 development board to get data from the mpu6050 sensor. I want to use bare metal code for the same. Is there any available code or sources...
Hi Folks!
I've got a rather bulky project that's having a rather bulky project. In short, my project tries to enable both MCUBoot DFU and an ExFat Filesystem. I've narrowed...
Support,
I've encountered a challenge while integrating my product with device from a third-party. Unfortunately, they've utilized the SIG base UUID for their unregistered...
