Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I've recently began experimenting with the HID service and connecting to iOS devices in order to achieve lower connection intervals with Apple products (as described in their...
Does ncs 2.5.0 implement the suggested workaround for https://docs.nordicsemi.com/bundle/errata_nRF52840_Rev3/page/ERR/nRF52840/Rev3/latest/anomaly_840_219.html ?
If not...
Hi
We met the problem is that clock low time period is out of spec, we got the value from oscilloscope is 1.24us@pull up resistor 10K/7.15k when clock speed=400kHz. The...
Hi
About nRF52840 I2C data read (CLK rate 400KHz)
1. Could you help check below three I2C items(tHD;DAT, tHD;STA, tSU;STO) can follow I2C standard(NXP) spec. or need follow...
Hi, having some issues with the matter door lock sample for the nRF54L15DK on NCS 3.0.2. I'm getting strange failures on boot when running the default matter door lock sample...
Hi,
using SDK 3.0.2 and build for the *ns target.
The idea is to put the CPU to sleep and while it is sleeping GPIO events (e.g. button press) shall increment a counter...
I have several applications that continuously scan on Bluetooth that have started exhibiting a new failure mode after upgrading nrfxlib from v2.9.0 to v3.0.2 ( https://github...
For our custom nrf9151 board,
The following is the prj.conf:
There are no pullups on any GPIO and for now, assume there are no peripherals connected, but there is a...
Hi,
We are having issues with this part bridging on our via-in-pads. We are using 2oz finished outer layer copper.
Do you have any footprint recommendations for 2oz copper...
Hi,
I would like to know the value of the Noise Figure for the nRF52840. How much dB is it? I am looking at the documentation of the nRF 52840 but could not find the value...
Hi Nordic team,
I'm currently working on a device onboarding flow using the nRF Connect SDK Toolchain v2.6.0 on an nRF52840 board . The onboarding process involves:
...
I am building the sample project C:\ncs\v2.5.0\nrf\samples\bluetooth\peripheral_uart, which supports MCUboot’s serial recovery of the networking core image on nRF5340DK. ...
My Power Profile Kit (PPK2) having issue after a firmware update. Now it's not even turn on the light when connected and with power switch on. I think I accidentally update...
My company does firmware consulting work. We have been asked to create a Green Power Device (Wall Light Switch) on the Nordic nRF52833 chip.
From our research It does...
