hello,
the function ble_stack_init () in the example of ble_app_uart are quite different from that in the example of ble_app_proximity in my first sight.
ble_app_uart :...
I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Hello, I'm designing a medical product, aiming at IEC 61000-4-2 level 4 ESD protection, and I have a question on the CC lines.
My understanding is that these two lines could...
Hi, I want to set different gap event length for different peripheral on a ble central: 1 link with high throughput and 4 links with low throughput.
The sdk is 17.0.2...
We are seeing our nrf54l15 based device remain in a high power mode after an ADC read using the latest v3.1 SDK (tested on both rc1 and rc2). This did not occur with the v3...
I've been trying to communicate with an external device which supports up to 25 Mhz on its SPI. So, to improve performance, I'm using the SPI3 at 16 Mhz. I have no issue at...
Hi,
I am trying to add an additional storage partition in flash to my project, however, to some reason, pm.yml file is not getting picked up during the build and I am not...
Hi:
I want to use nrf54l05 for the OTA function of BLE. In the example of l9_e5_stol, nrf54L15 OTA can running, but NRF54L05 cannot run.
NCS 3.0.0.
The part I modified...
Hi
I am using nrf70-wifi-ble-image-transfer-demo in the nRF7002 DK.
I change nothing on the code form the sample, after patching I have succesfully build the code and...
After updating to nRF Connect v3.1.0, I am not able to build a project that was started with v3.0.2, nor the matter template sample. When building both my application and...
Hello,
I have been evaluating the DECT NR+ physical layer with nRF9161DK boards with the v3.0.2 DECT Shell sample application. I am wondering if there are going to be any...
Hi Sir,
I have a question about these two configurations in overlay-ppp-cmux-linux.conf, CONFIG_MODEM_BACKEND_UART_ASYNC_RECEIVE_IDLE_TIMEOUT_MS and CONFIG_MODEM_BACKEND_UART_SLM_TRANSMIT_TIMEOUT_MS...
Hi,
I recently started working with the nRF9151 DK and was able to run the initial demo programs without any issues. To continue testing, I picked up a Thingy:91 X, but...
Good day, Nordic staff!
We are working on a product using the FLPR for its intended peripheral-controlling purpose. For us, the best way to send commands to and receive...
Greetings to everybody! There is some question about nRF54L15-DK board measured current consumption. I measure current via the P6 connector, that is, I measure current within...
