Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
Hello,
I've been playing around with the nRF52840 DK board and I want to make what I've been working on, into a PCB. Following the link below I've got the Altium files...
Hi !
I'm doing some testing on mqtt with the nrf9160 DevKit.
So far, everything is working with TCP and TLS and I would like to use WSS. I started with WS but I can't...
Hello everyone I'm doing my first steps so as to get things right from the start with a device based on the nRF52833 chip. My setup: PC <USB> nRF52840-DK <JTAG> CustomBoard...
Hello,
I am having a problem using DFU using the android NRF connect app. I have two separate projects that use the OTA DFU. These two projects have the same DFU code...
Now I want to construct a mesh network in an intermittent environment. You know the device will power off and power on frequently, I need to store the communication statin...
Hello All,
I have referred the reference example code to suit my needs. Below is my code,
Code is stuck at waiting for event. Didn't get callback with oversamping of...
Excuse me:
The client made a keyboard with nrf51802.，It has been mass produced。The customer reported that the keyboard and MacBook were connected and bounding before opening...
Hi,
We have observed that in areas of poor lte connectivity, the client_inti() works well but the mqtt_connect() takes a couple of minutes and times out.
I need to change...
Hi,
I'm compiling a piece of code that uses USB CDC ACM from a .cpp file, and I stumbled on the compiler complaining about out of order initializers in app_usbd_cdc_acm_internal...
Hi,
I'm trying to use Zephyr's 'http_client' library in Asset Tracker V2. I have included 'net/http_client.h' in main.c and have set 'CONFIG_HTTP_CLIENT=y' in prj.conf....
Hi,
I want Windows PC to communicate with nRF52840 dongle over USB full speed.
Are there sample of Windows software(likes API) and nRF52840 dongle ?
I want to realize...
Hello,
What is the limitation of the total current we can source/sink at the same time in multiple pins for low Vdd?
I could find a similar question (and answer of 15mA...
Hello there, I am working on a customized nrf52832 board. For the limited size, the 32kHz crystal is not install because I think the clock from 32khz crystal can be replaced...
Hi all
I want to do a device firmware update via the bootloader, and I am unable to do so, as all attempts end with a disconnect from my Android phone (Pixel 4a). I can...
Hello!
Hardware: nrf52840 IDE: Segger Embedded Studio SDK: nrf5 SDK 17.0.2
I've been having issues with receiving USB HID IN reports on Android. If I send at an interval...
