I am getting following error:
Error in final launch sequence
Error executing step execute method: stepInitializeJTAGFinalLaunchSequence
java.lang.reflect.InvocationTargetException...
Dear Nordic people,
I am playing (6.0.0) with sd_flash_page_erase() and sd_flash_write() , seems to be working ok, Allways happens what I do expect, but I am not able to...
Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
Hello,
I would like to add a costom cluster,controlled by custom App.I add cluster xml file,and run zap_regen_all.py to generate corresponding code.Everything is ok, the...
I am testing the current consumption of SIM cards with PPK2.
When PPK2 is connected to VCC ( voltage 1.8 v or 3 v ), the PPK2 can display the current properly ( around 9...
Hello I need to read the current mesh IV index of a provisioned node. Found 2 structures with the iv_index field : struct bt_mesh_cdb bt_mesh_cdb and struct bt_mesh_net bt_mesh...
When I package the firmware with nrfutil v7.12.0 version， I pack with a command like this
I got the right app.zip，manifest file
My question is: In nrfutilV7.12.0,...
I am planning to perform encryption using the CC312 accelerator on the nRF5340. I would like to evaluate the power consumption when using the accelerator.
My approach is...
Hi,
I am using nRF5340 DK and nRF SDK V.2.6.1 for my project
I clone the project from git and try to build the project using custom board but it is giving the cmake error...
1. When adding CONFIG_PSA_CRYPTO_DRIVER_CC3XX=y to the configuration as shown in the diagram, does it enable the use of the CC310 accelerator?
2. My understanding is...
We are making ZigBee product. The base we have took is from nrf connect sdk samples light_switch and coordniator example. everything works fine but we need to keep some information...
"I am working on a project involving Matter over Thread using the nRF52840 development kits. My goal is to pair and communicate between the light_bulb and light_switch Matter...
Dear Devzone,
I'm using 52832，SDK 17.0，keil.
What apis should I call if I want to enter the bootloader mode from my app? For example, I receive a message from a serial...
Hi,
I'm trying to do DFU on a custom designed Bluetooth peripheral device using nrf connect for mobile application. I can able to perform DFU successfully is some mobile...
I am working on RTOS that does not have WiFi driver for nordic wifi chips. I would like to port this driver to that RTOS.
In the documentation there is a mention of platform...
Hello everyone,
I’m facing an issue with step-by-step debugging in VSCode using the ARM GCC compiler with an nRF52811 microcontroller and Nordic’s SDK 17.1.
Here are the...
nRF Connect SDK 2.6.1 + nRF52832
I can't get the execution of shell commands from mcumgr over SMP to work.
Here is my prj.conf :
I registered some custom shell commands...
I have an application I have been developing in NCS v2.3.0. I'm trying now to updata to v2.4.0.
The application targets NRF5340.
It uses NSIB (b0/b0n) and for the application...
