after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hello, as the title suggests. I'm just wondering if the nRF91 (nRF9160 or nRF9151 DK) can use vanilla Zephyr instead of NCS for getting GNSS data (using the GNSS API)?
I...
I am using a STM32 with the NPMX drivers.
I am having a few issues and wanted to see if there are recommendations.
Issue 1:
disabling the interrupts does not seem...
Dear Nordic Community, I want to build samples/basic/blinkly on nordic nrf52840_dongle inside my Zephyr workspace. I use Zephyr 4.2.0, but on Zephyr 4.3.0 I have similar problems...
Hello, I am looking at pages 871 and 872 of the datasheet for the QFN48 package, but I’m not sure I understand correctly. Could you please tell me which GPIO P0 pins can be...
I’m using an nRF54L15 evaluation board obtained from a distributor and currently testing transmission and reception of large data chunks. Everything was working fine until...
I have an external device. After connecting it to the central device, I found that the Bluetooth service of my external device couldn't be enabled properly. When I checked...
Hi, I have the radio_test example running correctly on a nrf52840 dev board. I am able to use the Nordic Serial Terminal (v1.6.0) to send commands and read responses.
...
I am developing a custom board using nrf54l10 chip. So far, I have been able to use a code to comunicate through spi and uart for me to use printk function.
Now I was trying...
The docs( docs.nordicsemi.com/.../dect.html say that th nRF9151 modem can't do GPS/LTE and DECT NR+ at the same. Could the modem switch between the two operation modes while...
Hello team,
I am using SPI00 of NRF54L15 to communicate with w25q32fv (spi Flash). Below is the configuration I set in .overlay file
And below is the code I am using...
Hi,
I have a question about the the fields " tod_toa_reflector" and "toa_tod_initiator" in struct bt_hci_le_cs_step_data_mode_1.
I understand that these values represent...
The e-mail contains news of a new use of the nRF9151 module but uses the word "proves" and as an English language Cambridge qualified teacher I must mention that the word...
Issue description
I am using SAADC in single-ended mode with 3 channels (0/1/2). Measurements are performed by enabling SAADC, running offset calibration, configuring the...
Hello,
I have an application running on legacy NRF SDK and using the nRF5 bootloader, which has below flash sectors, 0x00000 - 0x026000 - Soft-device section 0x26000 - 0x0D9000...
