I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
I built the SMS sample without changing anything. I am using a Lebara prepaid sim card. I was able to exchange SMS messages from one cellular phone to another. I checked with...
Hello,
For a long range test between the nRF Toolbox Android app and the ble_app_hrs (in nRF5_SDK_17.1.0 package) over the nRF52840-DK. I would need to setup this board...
Hi,
I initiated pin 28 as SCK of SPI as normal condition, and I'd like to switch pin 28 as GPIOTE while receiving a command via BLE.
Basically this is how I achieve...
Hi,
I have loaded a simple application on my nRF52840 that just activates a GPIO as soon as it reaches the main loop.
The SoC is powered externally according to the chapter...
Hi,
We will create a ble peripheral device and also can handle timing-critical uart request. The uart will be always communicating and response time can't be slower than...
Dear DevZone:
I am developing an evaluation board with the nRF9160 SiP model, but I have some doubts with the software. Does nRF9160 SiP come factory preloaded with any...
Hi,
I try to implement Serial DFU update using the info in the " Add DFU support to your application " at link
https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides...
Hi Team,
When the slave side of the SPI received data from the master side, I want to log the received data to judge If it is right. But, I want to print it by log. it can...
Hi,
I am running some tests with the long range example provided by Nordic and observed this behavior which I can't account for.
https://devzone.nordicsemi.com/nordic...
path:
\experimental\cli\cli_agent_router\pca10059\mbr
When I execute "bdb start" in the serial port and then execute "bdb Legacy Enable", the terminal devices that are...
Hi,
I report some problems.
I have been using keil5,it work well. Because nRF Connect SDK doesn't know Keil
now i have used Segger Embedded Studio for a period of time...
Hi everyone. Here is my code for 2 different timers that put uc to sleep and wake it up(supposedly)
Definitions:
Create Timers:
Handlers:
Main() function...
I am working with the nRF5340 DK.
I am looking to sample an ADC pin to sample at a sampling frequency of at least 1kHz and I would like to use DMA to write the data directly...
