after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi,
It seems like there are many instances of ASSERT/NRFX_ASSERT that execute crucial checks prior to actions like dereferencing pointers, and they perform a reset if the...
Hi,
1-I have successfully developed an app ... \nRF5SDK1702d674dde\nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_template. 2-I have set a UART example to send...
Hi,
We have some questions from one of our FW guys regarding the configuration of the UART pin:
I looked at the UARTE driver implementation, it configures the UART Rx...
Hi there,
We currently have ~500 nRF52832 devices running nRF5 SDK (bootloader, S132, application). These devices are updated using the nRF5 SDK Secure Bootloader UART DFU...
Hi,
I would like to know if it is possible to configure the optimization level only the application built on top of Zephyr, and not all the project.
I am trying to debug...
Hi-
We have an application that currently does not use the soft device. Eventually we will want softdevice S113 in our application once we start to add some BLE based...
*** BEGINEER ALERT ***
Just thought I'd throw that alert in, so you are aware you can't assume anything in terms of base level knowledge here! I'm coming from a Cypress...
I'm currently playing around with learning how to code in VCS with nRF Connect. I was watching a series of Youtube instructional videos ( https://www.youtube.com/watch?v=MGsZJpdLtco&list...
Hello,
My colleague and I created ESB prx project based on SDK 1.6.0 version and nrf5340 dk.
And some source codes in ncs/nrf/samples/esb/prx/src folder are changed...
Hello,
I am trying to work on a simple GPIO program for the Thingy:91 which involves reading a pin for sensor inputs (this will be 2 sensors eventually). I have tried to...
nRF Connect V 1.6.0
using samples/zigbee/network_coordinator against a nRF52840, I am trying to commission a larger number of devices to join the network. Currently 24 devices...
Firstly, my english is not good,
I am using nRF52840 and my IDE is Keil uvision 5, i want to know, where is the pins SDL and SDA
I am new developer, and please you can...
I have successfully formed a mesh and sending data in the format as below
" udp send ff03::1 1234 $01 " to udp '1234' socket
" udp send ff03::1 1234 $02 " to udp '1234...
Hello everyone,
I am currently testing the range of Nordic BLE modules for an indoor application. I am using BC805 (nRF52805) as peripheral and BM832 (nRF52810) as central...
