Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I want to use ncs to get the RSSI at 10ms intervals.
For example, central receives an empty packet from peripheral at 10ms interval.
I would like to know if there is a...
Is it possible to set up an NRF Connect SDK project such that the firmware can be updated over BLE, without including the SoftDevice in the update?
I'm using NRF52810 which...
Hello,
i have searched for uart, i2c/twi communication with polling, interrupt, DMA method different brief explained guide for NRF52
but i have not found it any where...
Hello,
Previously, my nRF52840 DK worked perfectly fine through the USB (J2) connector. Then I successfully programmed PCA10059 by Debug OUT(P19) of the nRF52840 DK board...
My Android app allows the user to un-provision a mesh node. To do so, the app just sends a ConfigNodeReset message to the node's unicast address, which works perfectly if...
Hi, I want to add some auto-test capability to my nRF5340-based project. I thought one useful feature would be to measure voltage AND current at the hot node when all devices...
Hi all
We are switching to nrf-sdk v1.6.0 in our project and encountered a problem with MCUBoot.
The image builds successfully and can be flashed successfully as well...
Hi,
Iam using SDK 17 ,s140_nrf52_7.2.0_softdevice on NRF52840 SDK.For the first time I have noticed an issue,as below on running sample nordic17.0.2\examples\ble_peripheral...
I would like to use the Arduino Nano 33 BLE with MCUBoot and MCUMGR for FOTA. I am wondering if it is possible to use a two-stage bootloader (first stage Arduino BOSSAC, second...
I'm wondering whether the value pointed to by "ble_gatts_hvx_params_t.p_len" passed to sd_ble_gatts_hvx is copied to SoftDevice-owned memory before the call returns NRF_SUCCESS...
Hi,
I would like to create a library for the Nano 33 BLE to be able to use the NFC features that are available via the nRF52840 chip.
I am aware that there are some examples...
I'm starting a new product development using nRF52832, SDK 17.0.2 and softdevice S312.
Should I use v6.1.1 or v7.0.1 of S312?
Nordic's docs for SDK 17.0.2 state that S312...
I have no idea about how to read the device id of the external flash in the nrf52840dk? Please guide me to do so.
I also referred the MX25R6435F datasheet, to see the method...
