Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello Everyone, I am generating firmware hash using an hash function provided by an external library and using CODE_START and CODE_SIZE macros in app_util.h , So i wanted...
Hi,
We are currently testing the zigbee_light example for nrf52840dk. Once in the debug stage, if we pause program execution and then resume it we find out that codes gets...
Windows 10
nrfjprog version 10.10.0
jlink mini - connected to Windows 10 USB port, try to run any nrfjprog command and it says there is no debugger connected to PC.
...
EDIT: I incorrectly reported the Secure Bootloader pca10040_s132_ble_debug .hex file included in SDK 16.0.0 wrote to addresses in the mbr_params_page, I have since identified...
Hi,
I am using ncs 1.5.0 and modem firmware version 1.2.3.
if I keep CONFIG_HEAP_MEM_POOL_SIZE=8192 then my application runs without any issue but
If I set CONFIG_HEAP_MEM_POOL_SIZE...
Hello,
We are implementing NFC functionality on our product. Specifically we're using the Type 4 Tag (Read/Write). Are there any compatible NFC reader/writer modules? I...
In my product I use certain GPIO pins configured as input with the pull up activated to act as sense inputs connected to momentary switches to control the application firmware...
Hi all
I have developed a project on the nRF51-DK board based on the proprietary RF protocol.
Now I have a custom PCB board always with an nRF51822 but only equipped with...
Hi, im running the sdk version 1.3.2 and Im experencing a system crash after calling
spm_request_random_number after the 4th or 5th time
I've already done some research...
Hi i was trying to use simple mqtt sample provided as example with location " ncs/nrf/samples/nrf9160/mqtt_simple" the code was build and run but during lte connection it...
In PCB phase of the product, I used mt8852b to conduct the ble measurement test,When assembling the finished product, I want to verify that the Bluetooth connection is good...
Hi Nordic team,
Summary: Shall we get nRF5340 based BLE mesh demo to test data relay from one node to another node.
Details:
We requires BLE mesh demo sample for testing...
Hello guys.
We use NCS v1.4.2 and Zephyr RTOS to develop the application code for our nRF52840 SoC.
Thanks to your support, we were able to use Zephyr ADC APIs and take...
