after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
When using an onomondo softsim with all security features etc enabled, and using fota on external flash. nrf9151DK. NRF V3.2.3.
How is it possible to make changes to the...
Hi there,
I'm working with the nRF54L15 and using the light_ctrl sample from the Bluetooth Mesh SDK NCS3.1.0 .
I have a set of mesh light nodes, and I configured power_on_up...
Hi all,
I read in some thread (that I am unable to find now), that when stopping the SAADC via STOP Task, the STOPPED event fires (which is expected), however the END event...
When I run the Asset tracker template and look into nrfcloud I see new messages coming in on the terminal and Battery graph set correctly to 32%. I noticed already a long...
Hi,
I am currently sending SAADC data from an nRF52840 to a smartphone using BLE notifications. The SAADC is triggered by TIMER + PPI, and samples are collected into a buffer...
Hi Nordic Team,
I’m observing ~60 mA (or higher) current spikes while measuring with Power Profiler Kit II (PPK2) on an nRF52833 . Outside of these spikes the system sits...
Hi, We are using NCS v3.0.2 on nRF5340+nRF7002.
We have an error when doing matter commissioning using our own generated CD, PAA, PAI, DAC and factory data, see error below...
Hi:
I would like to use the Device_credetials_installer.py script to generate and install device certificates (including public/private key pairs) for the device.
ncs...
Hi,
just got my PPK2 and noticed some strange behavior:
the only thing connected is USB data/power, no DUT. Power output is off. If you start logging it displays some...
I'm using nRF SDK 2.3.0 in VScode, which I recently upgraded. It compiles my firmware correctly, giving me some warnings. The problem is that clicking on the warnings points...
Hi,
I am developing with NCS 3.2.3 on the nRF54L15.
I need to customize the FW loader located here: github.com/.../ble_mcumgr
The customization is related to the BLE...
hi,
i'm learning this exercise and when i add the code for external flash partition, why i didn't see the size for this external flash in memory report.
and maybe it...
Working with the new v3.3.0-preview2, I have found an issue. You may already be aware, but here it is.
Issue
Steps to reproduce
Add these kconfig settings
...
Hi everyone,
I’m working with three nRF9151 DKs to evaluate DECT NR+, and I’m trying to understand what level of multi‑hop or mesh networking support currently exists...
Hi,
I got a confused problem. Using NCS V3.2.0, I develop a firmware with mcuboot. Everytime I flash nRF54L15, There is an error occurred. Here is the message:
Error:...
