Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
I have an application where I use the bt_gatt_write() method and I would like to obtain information about the number of packets sent in my operations.
I would like to know...
Hi,
I am baffled by the QOS handling (and/or not handling) in asset_tracker_v2, especially in view of the fact that there is a QOS library as part of the nrf repository...
Using the nRF Connect Desktop application and the nRF Connect SDK for my nRF9160dk.
I would like to monitor RAM usage during runtime of my program. In particular I am interested...
Hello,
I am trying to migrate a project nRF Connect SDK v2.6.2 to v2.7.0 for the nrf5340dk target board, particularly to update to the new hw model v2 and sysbuild. I am...
Hello,
I am using nRf21540 and nRF5340 in GPIO+SPI config, where SPI is controlled via MPSL and separate spi0 bus.
I have configured the board files based on nordic,nrf21540...
devicetree overlay file
// * Connecting ADC channels
// For more help, browse the DeviceTree documentation at docs.zephyrproject.org/.../index.html
// You can also...
I just ported your AWS IoT for MQTT from this repository .
If I keep IPv6 enabled, I can get the address information without any problem. However, if I disable IPv6, the...
I have a project that runs fine when CONFIG_BOOTLOADER_MCUBOOT is disabled, but when I enable it pins 15 and 16 are pulled high. I need the mcu bootloader to run but is there...
Hi All ,
Setup Used
nRF Connect SDK v2.7
VsCode
Ubuntu 20.04
Google Nest Hub2
Android 12 Smartphone + Google Home App
nRF 5340 DK
Endpoint-0 ---------...
Hello Developers,
I am k.hemasundar and i am working on the nRF52833 QAAA0 micro controller with segger embedded studio IDE. I have used nRF SDK of version 17.1.0 and 16...
Hi,
I have to develop a BLE peripheral, that communicates larger amounts of data over L2CAP. Establishing the channel between central and peripheral works. I'm able to receive...
Hello,
For the evolution of a device that uses a nRF52832 and 2 SPI's instances we are evaluating the option of adding 2 new UART's instances for managing 2 serial peripherals...
Hi there,
So, this is in a sequence of attempts to read data from a digital microphone SPH0645 using i2s master protcool on nRF5340. The program layout is as follows:
...
Hi there,
I am trying to interface SPH0465 microphone with nRF Dev Kit 52832 with the following configurations of I2S:
I have followed the code from echo example...
