after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
hi guys,
I am using the nRF54L15 for software development. I have a requirement to define a space in the chip's internal flash for data storage. I referred to the soc-flash...
I have been experience that the if the device under a DFU process reports the error BUSY, because the external flash on the device is used for fileaccess the DFU process from...
Hi nordic support:
Our product uses the nRF9151 and prepare for GCF certification testing , which need to capturing LTE mode trace log .
We first intend to try running...
Hello everyone,
We are currently working on a project that uses the nPM2100 to power an nRF52840. Our application requires automatic enabling break-to-wake mode each time...
Hello DevZone,
One customer used Timer+PPI+GPIOTE to simulate an UART. Now it works fine.
However, when there is other timer's interrupt, the simulated UART may lose some...
Hi, I just received our nRF54LM20DK, and am trying to get a functioning BLE sample on the board. Many samples are supported, however I have not gotten a single one to work...
Hi,
I have a question about SPIM. Is it possible to have two events via DPPI that will start different SPIM transfers for the same SPIM channel?
What would happen if a...
I have the board: NRF52840-DK PCA10056 3.0.3 2026.5 1050266921
Is it possible to use OB J-Link to debug STM32/RP2040 MCUs connected to P19/P20? Or OB J-Link support limited...
We are using CMakePresets.json extensively in our project and rely on the condition field to control which presets are visible depending on the host system.
However, it...
Hello,
We are using the nRF52840 with SDK 17.1.0, SoftDevice S140 v7.2.0, and the secure bootloader (nrf_bootloader.c).
Our application relies on reading NRF_POWER->RESETREAS...
Hi there,
One of the functions of the DECT MAC layer is to allocate radio resources to RDs. According to the standard, the MAC layer does that using special beacon messages...
Hi,
I'm working on a wireless sensing project using the nRF54L15-DK (PCA10156) where I need continuous RSSI measurements at 2440 MHz. I'm accessing the RADIO peripheral...
Hi,
I am working on an nRF52832 using nRF5 SDK 16.0 and I am seeing inconsistent behaviour in the RESETREAS register. During a power-on reset, the value is usually 0 but...
Hi!
We are building an application for Thingy91X and noticed that there is an overlap between the shared memory between the app and net mcus, sram0_shared, and RetainedMem...
