Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hello DevZone team, I recently received a new nPM1300 Eval Kit (PCA10152, 1.3.0, 2025.19) and connected it the first time following the documentation ( docs.nordicsemi.com...
Hello,
We have a custom nRF54L15 board, that, when powered with 1.8V, shows a too high power consumption. 230uA in system on - low power mode, and 12uA in system off mode...
Hello Nordic Team,
I am working with the nRF9151 DK and exploring audio output using the TLV320DAC3100 DAC.
I see that I2C is clearly available in the DK schematic , but...
Hi Nordic:
I use the nPM1300 to power the NRF5283 and external sensors. The nPM circuit schematic is as follows ， Please check for any unreasonable parts.
1 Charge and...
Hi All,
I try to connect nrf9160 to our azure space ( Azure IoT Central) using sample : sdk-nrf/samples/nrf9160/azure_iot_hub at main · nrfconnect/sdk-nrf · GitHub
...
Hello I already have a team on the PRO plan on nRFCloud and I would like to create a new team on the nRFCloud, using the same user as owner of both teams. According to: https...
Hello,
Is there an easy way to upgrade the CMake version that is used during the build process trigger from the nRF Connect SDK Extension in VSCode ?
I'm currently using...
I am using the older SDk 17_1_0 used in the Qorvo UWB sdk.
nrfConnect ->connected to -> controller ->connected to ->beacon, neither appear in scanner as expected once...
I can't define an Advertising file larger than 191 bytes, even in Extend.
Here's my code and proj.conf file.
My board is an NRF52840.
main.c
proj.conf
E...
Hello,
I'm working through the fundamental courses and trying to get my nrf54lm20 development board setup. After I have built and flashed the sample firmware to the dev...
I just upgraded my project (that runs on custom hardware with the nRF8233 using an Ezurio BL653 module) from nRF Connect SDK v3.1.0 to SDK v3.2.1 and the battery monitoring...
Hi, we have recently started developing with the nRF5340DK. We encountered several issues while configuring a FATFS on the external flash (mx25r64).
1. The sample code...
Hello
I am currently trying to develop an asset tracker based on your Asset Tracker Template ( GitHub - nrfconnect/Asset-Tracker-Template · GitHub ). While going through...
Hi,
I am trying to configure SWO logging in a sample project based on zephyr/samples/hello_world (source and config at the end).
I run this application on two targets...
