Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I just saw the announcement for PRS support. This is very interesting to us for use cases where GNSS reception is temporarily poor. Questions:
What do we need to...
Hi Support Team
Must inductors be placed between the SW1/SW2 pins and the VOUT1/VOUT2 pins of the nPM1304? Can VOUT1/2 output normally if removed the inductors? Many thanks...
Hi,
I am working on a BLE application using the nRF5340 SoC(custom board) and Zephyr RTOS (NCS SDK version v2.9.0)
When I call bt_enable(bt_ready_cb_t cb) , Bluetooth...
Greetings, all. I'm a rank beginner here with all things Nordic but almost 50 years of embedded experience with other devices, environments, etc. I'm trying to develop for...
Custom device using nrf5340, with NFC card emulation functionality.
To use the NFC, I understand that I should use the supplied nfc_t4t library (binary) and its api. I have...
Hello, I'm developing on an application which requires to catch high speed, variable size and bursty (~0.5 Mbit/s) data from a sensor connected to a nRF9161DK trough a UART...
I'd like to use the DeviceTree Visual Editor to create the DTS for a custom board starting with only the bare device. But it seems for some reason that the DeviceTree Visual...
Hello,
I’m using the Thingy91X board (nRF5340). For my application, I need to run BLE and Wi-Fi simultaneously, so I have to increase the application size. To do this, I...
Hi I'm trying to work on OTA implementation for zigbee with nrf52840-DK boards.
there is a sample available in ncs2.9.0,light switch,but i understand it can only work as...
Hello,
I have some issues to do function an ntc thermistor with a nrf54L15DK.
An error about a wrong configuration of the adc reference or or the ADC gain appears almost...
Hi,
I have some problem when scan advertising packet using nrf52840dk with ncs v2.5.0.
when I scan during 30s in the same position, I got a list rssi value same that...
Hi Team,
Hello Team,
I'm currently working on integrating the Sensirion STS40-CD1B-R3 temperature sensor into the peripheral_ht . To do this, I pulled the STS40 driver...
When I used the CS instance for distance measurement, I wanted to set multiple initiators. Therefore, I configured BT_CTLR_SDC_CS_COUNT to 3. However, I didn't know where...
Hi there!
We are currently evaluating a low-power BLE system for a safety-critical wearable application that must transmit immediate alerts to a nearby receiver or mobile...
