Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I use the ble-app-uart-c-multilink example with a nRF52840 DK and 5 custom nRF52840 peripheral devices.
For a test, I want to connect to only one of those peripherals...
I am a newbie in nrF52832. I have been carrying some experiments using the Nrf51 and so far they are going so well. However, I came across some few E104-BT5052 samples originating...
In ncs1.7.1, I’m struggling with a problem about hard fault on nRF9160, but I have no idea to slove the problem.
nRF52840 transmits data to nRF9160 via UART0, the baudrate...
Hi,
I got the example http://github.com/NordicPlayground/nrf52-ble-multi-link-multi-role and the demo is OK.
I also use nRF Connect APP to connect the ble_aggregator,...
Hi,
Hope you are doing good.
I run the SAADC signal to from the sdk and observed that when the adc input is connected to ground, the adc reads few random negative value...
Using nRF9160, ncs 1.6 on a custom board and segger-SES for debugging, we have intermittent stops (debugger breaks) on an assembler line with 'cpsie' opcode:
File: cpu_idle...
Hello Nordic support,
I am using nRF5 SDK for a Zigbee coordinator application. In zboss_api.h, I see that there are functions for setting short pan id (zb_set_pan_id()...
Hi, I'm starting a new custom development, that will use NRF52805 SOC. The project will be one Alexa Gadget device. I have seen several documentations, but I have some question...
Hi,
I have met one bug.
when I flash a fw with generic level server , then flash other fw with sensor server , the system runs error, if I use command "nrfjprog --eraseall...
Hi Nordic,
I have written a device driver following the guide as Devicetree HOWTOs , and try to call the driver api in main(), but got unexpected output as below.
I...
Hi nrf masters!
We have a problem quite late in a large development project and urgently need assistants. We have spent hour's reading all posts about this and debugging...
Hi,
I would like to know if it is possible to implement with nRF9160 a communication to an ethernet port?
Also if the nRF9160 has CAN bus port.
Many thanks, Jose
Hello, in my project, I don't want to create and develop my own module based on nrf52810. I want to know if there is any company that produces ready-made modules based on...
Hi,
I am using the SDK to develop a BLE application, I tried to merge two different projects and and I build the project, I have linking issues :
1> Linking ble_app_uart_pca10056_s140...
Hi Team,
we have one doubt regarding sleep current when we try to measure with power analyzer(nrf52840 EVM Board) .we got 5.23 micro amps instead of 2.35 micro amps. ...
