Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hi to all, I'm developing a new device that should be a multiprotocol: Zigbee (as coordinator) and BLE peripheral (nus).
I use the nrf5_sdk_for_thread_and_zigbee_V4...
Hi Everyone,
I'm working on "Thread_Zigbee_v4.1.0\examples\zigbee\light_control".
I need configuration as above title.
But I relize that "zb_set_pan_id(0x1234)", "nrf_802154_short_address_set...
I am trying to use the DK Dashboard with the Serial LTE Modem Software.
The connection to the Cloud works in principle but I only can see the terminal card when connected...
Hello,
Currently I am experiencing some problem getting the NUS to send a TX notification of more than 20 bytes to the central (which is an old custom android application...
Hello,
I am offloading sockets in config. I instantiate a socket, set the send/recv timeouts, and then call connect(). It's returning a 95 which is EOPNOTSUPP. I was able...
Hi,
I'm investigating firmware image signing on the nrf9160 using MCUBoot and the nRF Connect SDK v17. I have configured
and it seems to work via `west build -b nrf9160dk_nrf9160ns...
Due to parts shortages, we are having to scramble to find compatible hardware for our project. I have sourced some nRF5340 modules but need to know if Gazell is supported...
Hi!!
I am facing an issue wherein more than one device is acquiring the leader role in a same thread network.
In my setup, I have a total of 4 devices. Three of them are...
Dear Team,
I have to use many number of pages to store data in flash memory in nrf52840 , but I am confuse that what will be start address and end address in flash_fstorage...
Hello Team,
I am facing segmentation fault while reading the OTP memory using pointer in my code. To write the OTP value I have used below command which was successful and...
Hi,
I received the nRF9160DK yesterday, and used the AT Client to get talking to the modem and connecting to a network. In VS Code I built an application from sample ...
Hi there,
I'm using the product specification of the nRF52840 to program the SAADC in continuous mode using its internal timer. I'm not able to use your SDK. Unfortunately...
We've built a custom board, at power off current is 1-2uA and when connected average current is ~4.7mA. Internal DCDC is enabled, this shaved off >2mA. Other than reducing...
Hi ALL:
- SDK version: nRFSDK 15.3
- HW: nRF52832
I am tried to earse the flash by sg_flash_page_erase(uint32_t page_number), but still failed. My code snippet as...
