Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello,
I'm trying to program an nrf52 PCB I created from Arduino and code studio just trying to upload a simple blink but when ever I try to connect any of my ST-link...
Hello
I have defined the SPI pins in the sdk_config of the ble_app_uart example and compiled the code after adding the dependent drivers from spis project as shown in...
Hello,
when writing content onto the CDC-ACM interface of the nrf52840, I sooner or later always end up in a Segmentation fault.
I'm on nRF52840 and using the SDK v16...
I'm using the nRF52840-DK evaluation software from Segger. I want to add NAND Flash support, so I want to add an SPI interface. I have looked at the example in nRF5SDK160098a08e2...
Hi，we had finished application development on nrf52832 long ago, based on nrf52 sdk 14.0(with softdevice 5.0). But now we get feedback which is a bug has been fixed on sdk...
Hello guys,
I would like to know something more about the scheduler whose implementation can be found under SDK_ROOT/components/libraries/scheduler .
Our idea is to apply...
1. I don't want to call the fds function when enabling or disabling cccd: pdb_write_buf_store, so I did the following:
2. I am in nRF5_SDK_12.3.0_d7731ad in the sdk Routine...
Hi There - I'm very new to electronic design and need help making a key design decision. Specifically I want to know that the performance will not be a problem when writing...
Hi
On some devices we see in the production a shortcut between the BT antenna and the P0.18 pin on the 52811. The cause can be extremely warm weather at the production facility...
Hello,
We are tweaking the TLS connection between nrf91 and mosquitto.
What ciphers does the modem support? Is there a list available?
Best regards,
Vlad
I want to send a byte on Nrf connect app upon receiving an GPIO interrupt using BLE_APP_UART code. I have configured pin P0.10 for the GPIO interrupt. I am using SDK15.2.0...
Dear guys,
I am implementing a module that monitors the battery voltage for our tracker device using NRF9160.
I do not understand how to set up two parameters for the...
Hi:
The urgent problem we are facing now is:
debugging hci_usb on Linux, how to set MAC address and send/receive files ? hci_usb fw : \ncs\v1.3.0\zephyr\samples\bluetooth...
Hi, I have no found clear steps to create DFU zip packet for old one softdevice S132 SoftDevice v2.0.0.
I try to build with nrfutil pkg generate but seems its working only...
