Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi! I'm running a project with an nrf52 chip for which we use the JLink as the interface. I've been using my setup a lot for the past year. The other week, every LJink command...
Hello,
i'm trying to understand how the management of the SS pin is (or has to be) performed when using nrf9160 as SPI master.
In this post Håkon said that:
"Most driver...
Hi,
I using the radio test example on the pca10040 with nrf52832 EVB.
And set the radio test to Tx, the parameter as below:
Data rate: NRF_RADIO_MODE_BLE_1MBIT TX power...
I have searched the devzone and couldn't find any solution
followed the instructions from Nrf Connecta dn verified as well.. using
tag v1.1.0 (have done west update...
I'm using the MESH SDK 4.2.0 on a nrf52832 in combination with the Serialization interface (ACI) example
We'd like to implement the key-Refresh cycle and are planning on...
I am trying to setup (Nordic Edition) SES 5.10d for an example to download to the nRF52840 Dongle.
The tutorial* helpfully discusses how to avoid overwriting the MBR and...
I am using nRF52840-CKAA-R7 II2c to connect to my MSP430 i2c[ slave]. i have put any pullup on the clock and data thinking, to use nordic pull up in default. clock is connected...
Hello, all ..
I'm using nrf52 pca10040, s132..
I connected custom board and nrf52, and would like to communicate with uart. First of all, custom board is model cm1106...
I am looking to write my own IRQ handler for the UART. I read the post https://devzone.nordicsemi.com/f/nordic-q-a/46822/nvic-table/184731#184731
and added my own definition...
Hello,
I am new to Nordic and Segger. I am trying to build source code developed by a 3rd party. It was originally developed with GCC in Linux. I have followed some suggestions...
Hi,
I am working with nrf52840dk and using a peripheral _uart example from NCS v1.3.0. and the problem that I am currently having is that I cannot get it to low power. At...
Modem fw version: nrf9160_1.2.1
How to reproduce:
- Set AT%XSYSTEMMODE=0,1,1,0
- Open a TCP IPV4 server socket in a thread and wait for connection (i.e. accept). The...
hi，I want to use RSA to encrypt and decrypt transport data. I see some file: 1. \nRF5 SDK\nRF5_SDK_16.0.0_98a08e2\external\mbedtls
2.\nRF5_SDK_16.0.0_98a08e2\external\nrf_tls...
