Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I'm having a peculiar problem with my device in a memory heavy application, two of my libraries use statically allocated memory and one uses what i allocate with mem_manager...
Hello.
I'm working for a Zigbee networking project.I chose nRF52840 as the coordinator.The coordinator acts as a gateway to communicate with Zigbee 3.0 devices on the market...
Hi. I am trying to add FDS to my application where I used freertos and ble. I tried few things always ending with hardfault, one time it was from Freertos scheduler and the...
Hi
I have a problem changing the max_rx_octets and max_tx_octets parameters with the sd_ble_gap_data_length_update function. On request from the app the size is attempted...
HI, we have updated our DK firmware (mfwnb1nrf9160030123prealpha) for nb-iot but after inserting the Vodafone (Ireland) V-Sim we only have a flashing LED 3.
nRF connect...
Hi all
Chapter 26.1.1 of the nRF51 series reference manual v3.0 states that the pins used by the SPI master have to be configured in the GPIO registers according to table...
Hi, I am interested to learn THINGY 52 working
I want to know how does the Thingy52 works?. any tutorial to explain the function of THINGY52
How to delete the boot loader...
Hi
The example in SDK15.2 for 52840 as a Beacon is not long range (I think).
Is there another example that will enable long range and also to enable connection?
While...
Hello,
I'm use laird BL651 with nRF52810 module. I flash the chip with beacon program from zephyr samples. I use Segger Studio.
The chip is discovered by smartphone (with...
Hi,
is it possible to scan 10000 beacon having adv interval of 10 seconds. is their any maths or formul we can do ?
i have set nrf52 to scan continuesly,
Hi,
There have 4 PWM sample code (low_power_pwm, pwm_driver, pwm_library and pwr_mgmt) in SDK 15.2.
I my use case is "Control 6 PWM output with different duty-cycle and...
We have written an application based on SDK V12.2.0 using S132_V3.1.0 for the nRF52832 and have been dealing with an issue where the module constantly enters a hardfault....
Let's suppose the PC (a laptop) goes to standby while a BLE connection is established with a Nordic dongle using pc-ble-driver v4.0.0:
- With SD API V2, status handler is...
Hi
I downloaded and successfully build and ran the asset tracker sample on the nRF9160 DK using segger embedded studio. In a first step I want to reroute the debug UART...
Hi there,
I have a project where I am using the NRFX I2S Driver. I am using SDK 15.3.0 and SES 14.2.
In my sdk_config.h, I have the legacy I2S driver disabled and the...
