Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I tried to debug Asset_tracker_v2. During step by step debug, the program navigate to that part which is not included .. see the image. Also, I want to know, little more:...
Hello Devzone Community,
My name is Ted, and I am some way along development of Zephyr based firmware, running on an nRF9160 based custom board. I'm looking to put the board...
Hi,
How can we prove that the A-GPS is working correctly? We have run an experiment where we have use a module with A-GPS and one without and they have very similar (and...
Setup -
1. Sample used - nrf/samples/nrf9160/lte_ble_gateway
2. Board used to build - nrf9160dk_nrf9160_ns
3. NCS version 1.9.1
Steps performed -
1. Built the...
Hello Everyone,
I am trying to implement one wire protocol for interfacing MAX17211 fuel guage IC with NRF52840. I wand to know if there is any one wire library or any example...
Hi,
Do you have a suggestion for a 2.4GHz chip antenna? I sent a board to Ketil for RF tuning but the meander antenna ended up as too short. We would like to avoid a separate...
Hi there, I have been always using the dev board BLE antenna for the nRF52832-QFAB.. but now i need to reduce much more the size of the board, so i need a much smaller antenna...
Hi
I am currently trying to get the antenna switching working on the nRF52833 DK
I have an SPDT RF swtich is this pe42423
1.I want to use for switching.But I don't...
Hi,
I have a central-peripheral FW over a nRF52840-DK running NUS service and I have to measure the throughput between the nRF52840-DK acting as a peripheral of a mobile...
Hi
How do pass bat_num into the declaration for the power config attribute list? Perhaps I overlooked it, but it wasn't evident to me when reviewing the Developing with...
Hello All,
First, thanks for this post: https://devzone.nordicsemi.com/f/nordic-q-a/40924/how-can-i-restore-the-original-bootloader-of-a-pca10059 ; I'm attaching the file...
Hi. In nrf52840 is it possible to use in NRF_LOG the second UART (DMA based) ?
I know i can define the TX pin in the SDK_CONFIG but can the NRF_LOG_BACKEND_UART work with...
