Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hi,nordic team，
I'm developing a keyboard with the nRF52840 and NCS desktop, and it has a dongle. I hope Nordic's LLPM can reduce latency. But I can't find in the docs how...
If I have an application where I have implemented USB CDC-ACM, how can I set the serial number seen by the PC when I connect my device? Is it possible to set it at runtime...
Hi,
I am implementing discovery service but getting undefined error with below
bt_dis_pnp_params pnp_id = {
.vendor_id_source = BT_DIS_VENDOR_ID_SRC_USB,
.vendor_id...
Hi!
I’m developing an application using nRF SDK 2.9.0 with the Xiao BLE Sense . I created a new project based on Zephyr’s UART peripheral example.
The application runs...
I’m trying to implement DFU upgrade of NRF5340, I can send the image (./build_5340_app/build/signed_by_mcuboot_and_b0_s1_image.bin) to the device when running and it seems...
According to the documentation, you should run azure_iot_hub_dps_reset() in order to force DPS registration again.
But if the device has previously been enrolled and a device...
1. What is the Bluetooth version in NCS 2.6.1?
2. How to get Bluetooth version from NCS? is there any variable? I cannot find it in the release note neither. https://docs...
Hello,
I am using nRF Connect SDK v2.9.0, and nRF54l15 board. I enabled the watchdog timer and used its driver in zephyr/drivers/watchdog.h
It seems to work fine. The...
I have checked the PWM library in the nRF Connect SDK, and it seems that the library does not support init and deinit functions. The function pwm_set_pulse_dt(&pwm_led, 0...
Hello,
I’m currently working with a custom board based on the nRF9160 SiP, and I would like to measure the LTE-M TX power after the antenna impedance matching circuit. Ideally...
I am using the nrf52840 chip on a custom made PCB that is powered by a USB-C which provides it with 5V.This 5V is then converted to 12V using CH224K which then is wired to...
Hi,
we have ESB PTX and PRX couple from nRF54H20 nRF54H20DK (rev. 0.9.1), SDK: v2.9.0-nRF54H20-rc2 and the same Toolchain, IDE: VSCode + nRF Connect plugin build for CPURAD...
Using wireless sensors with nRF54L15, the sensors do not need to be connected, only broadcast a small amount of information. There will be 50-60 thousand nodes, and they are...
Hi, I'm trying to setup serial recovery in my project, in order to update firmware via USB cdc-acm.
I'm following this exercise from the academy which seems what I need...
