Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
Hello,
I am using the nPM1300 IC on a custom PCB with the nRF5340 + nRF7002 + nPM1300 configuration. sdk v2.8.0
I am trying to read the battery status (ADC value) via...
I have problems when I connect to my mqtt broker, it looks like it doesn't do a CLEAN_SESSION.. according to server logs.. I see when I connect to test clients ( pc ) with...
Hi, I recently purchased a nRF52840 dongle with the intention of creating a Bluetooth mesh provisioner with it. The first thing I tried was flashing the mesh_shell example...
Hi ,
Could anyone please with NRF9160-SIAA-B1A-R7 CAD Files (symbol, footprint, and 3d file) for KiCad ?
Thank you for your support.
Best regards, Mohamed Obaid
I'm using an nrf52840 on a custom board and send debug messages with printk to RTT. When mcuboot is added to the firmware it is no longer possible to read the messages from...
Hi nordic support Team.
I try to build blinking led example: nRF5_SDK_17.0.2_d674dde\examples\peripheral\blinky\pca10056e Load firmware for NRF52811 and NRF52840, i see...
Hi,Team,
I am developing Long Range and Pawr using nrf54l15-dk.
For the Long Range example I refer to E:\NCS\v2.8.0\nrf\samples\bluetooth\central_and_peripheral_hr and...
We previously used the nRF52832 (with Segger Embedded Studio) and implemented OTA updates for it, along with developing a custom APK.
Now, we are using the nRF5340 (with...
My nRF52840 DK needs to interface with a convential device using the data bus and address bus. The following diagram (P.27) from the nRF52840 PDK user guide.shows the data...
Hi,
I got a question on IQ Sampling with the direction_finding_connectionless_tx/rx example.
Settings:
Sample Spacing = 125 ns
Sample Sapcing (Reference Period...
Hi,
I have an nRF5340 DK, and my BLE project runs fine on it. However, when I flash the same code onto my custom board, bt_enable() returns error -11 , which seems to...
Hi
In the newer versions of nRF Connect for VS Code, the NCS and toolchain version can be configured per build-configuration.
Is it possible to configure the desired versions...
Hi all, will need to post short as I am getting a "cannot create ticket" error.
Hi all,
I'm quite new to nrf, zephyr and embedded of this complexity but have completed...
