I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi!
I just upgraded a product we developed using a Fanstel BT840X module (nrf52840 with a Skyworks SKY66112 amplifier) from SDK 2.3.0 to SDK 3.1.1 and I noticed that our...
I'm planning on using an e-ink display with my custom PCB . But when I add/enable the e-ink display node in my device tree, the TF-M code throws an exception in /ncs/v3.2...
Hi,
The attached screenshot shows a section of an air-trace for the 5340 running a commercial LE Audio stack. From the rising edge of the logic inputs, it can be seen that...
Hi List, I am using ZMS to log data. While performing stress tests, I see few issues:
Including zms in the projects makes the application boot time delayed. The delay...
Hi there,
Several examples of the course include a configuration file and an overlay file for the nRF52840 dongle. However, the code cannot be compiled. The problem seems...
Hi everyone,
I’m trying to use the HTTP client sample from NCS v3.0.2 with a W5500 Ethernet shield on an nRF5340. DHCP works fine, and I can successfully POST and GET using...
We are using the Murata Type 2FR dev kit - https://www.murata.com/en-us/products/connectivitymodule/wi-fi-bluetooth/overview/lineup/type2fr
Internally, this has NXP's RW612...
I'm running the subrating sample (ncs\v3.1.1\nrf\samples\bluetooth\subrating) on two nRF54L15-DK boards. Using a protocol analyzer I'm seeing that when the subrate factor...
Hi there,
Just a minor flaw in the exercise, but a question concerning the callback from the event “le_param_updated”. In the solution to query the connection interval,...
One of my customers currently has a requirement similar to the one discussed in this ticket:
In their product, the main controller is a BES2610, and the Bluetooth functionality...
Hi
According I2C standard, there is a requirement regarding falling speed of SCL/SDA which is > 20*1.8/5.5=6.54ns, and our measurement result of Tf on SCL is 5.732ns.
...
Hi
I am using the nRF7002 DK with NCS 2.7, based on the sample project `nrf70-wifi-ble-image-transfer-demo`. I modified the code to embed a fixed image as a header file...
Hi
In nRF5340 datasheet I2C frequency only have 4 selection as below
But when ask your AI, he response below
Important errata at 400 kHz
For all nRF5340 revisions...
I would like to trigger a hard reset when valid voltage is first detected on VBUS. How could I do this with no or minimal external components and without a complementary MCU...
