Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
In my project, nrf52832 used as a communication module.
In order to let user's phone reconnect automatically,I add HID service,appearance and uuid into advertising packet...
Dear Nordic Team, we are using the adafruit_feather_nrf52840 and nrf52840dk for our prototypes and recently the toolchain around nrf and zephyr has become a problem. Build...
NCS 2.7
NRF52840
I have 2 different applications: app and mfg_app
I have 2 different boards: small_flash and big_flash
I need to build all 2*2 combinations.
I...
Hello,
We were developing on an nRF52840 board with the NCS 2.6.1 SDK and had configured logging and shell capabilities via UART. Once we moved to the 2.8.0 version, we...
Hello Everyone,
Happy New Year !
We would like to evaluate nRF54L15 system off/deep sleep mode current consumption. So we have tried the existing example ( https://github...
We could have found "transmission delay" in 2ch Audio recording sequence.
Here are the detail about the environment of DUT, and phenomenon.
Please find the attached file...
I'm updating my development environment to new PC.
I've downloaded and installed nrfConnect.
The toolchain manager on tje new PC only references SDKs 2.7.0, 2.8.0 and...
Hi,
I have 3 NRF52840 dongles plugged in a Raspberry Pi 3B+. One of them is used to communicate with my phone with BLE, and on the two others I have loaded the NRF Sniffer...
Hello,
I want to test nRF21540 EK with a nRF5340 DK.
I am using ncs 2.7 , and don't want to use sys build . I want to use child image/ hci_ipc .
I modified ncs/zephyr...
Hi, I've noticed a strange behavior of my device. I'm using a nRF9160-based custom board with nCS v2.6.0 and modem version 1.3.6. Long story short - after trying to acquire...
I've setup my development environment using the 'application' structure. https://docs.nordicsemi.com/bundle/ncs-latest/page/zephyr/develop/application/index.html#zephyr_workspace_application...
1.
2.
Hello. It is under development as nrf7002.
I'd like to ask you about the quasi-board configuration I saw in the sample example.
The target board in...
When I build the system using system default, use save minimum configuration，The chip-related configuration is also saved to my application configuration prj.conf, which it...
Hello everyone,
I am currently using Nordic NRF5340-DK board for development and I have run the zephyr UART driver sample that works an echo bot. This sample works fine...
