I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
I made a PCB board, but I couldn't connect to the chip with JLink. I used a lithium battery to power VDDH. I want to test if there is any problem with the hardware. I tried...
I am using NRF5340 with NRF connect (Zephyr) and logging out to RTT (printk or printf, etc) , which works but sometimes I get buffered fragments and dont see the rest of the...
Product: nRF54L15, SDK:3.0.2, door lock application
Hi,
When the Matter door lock removed from Apple Home(Home App, remove accessory), the lock does not remove all the...
Hello,
I am experiencing an issue when trying to flash any program using nRF Connect for VS Code. When I execute the flash command, my board disappears from the "Connected...
Hello,
Is there support for fuel gauge algorithm with the CR2450 and the nPM2100 implemented? If not, is there a plan to release support for it soon?
Thank you,
Fin...
Hi,
We need to write binary content from a binary file (.hex or .bin) to a specific area of the external flash (QSPI).
According to this topic: , this is similar to our...
Hello,
I have been trying to get my brand new nRF52840 Dongle working as an 802.15.4/Zigbee sniffer, but I am not able to capture any packets, even though the interface...
I compared the S132 and S140 protocol stack files. The S132 file does not occupy the 0x26000 address, while the S140 does occupy the 0x27000 address. However, the application...
Hi, I've spent a few hours trying to figure out a way to use the onboard PDM microphone on Thingy52 with the nRF Connect SDK.
I saw a pull request for one from a member...
Hi nordic:
I am using NCS 3.0.0 and VSCode. I was able to compile the sample code in the SDK some time ago, but now I am getting the following error when compiling the sample...
None of the buttons work, most errors are similar to as follows but specific to each button:
Error running command nrf-connect.app.createBuild: Could not find SOC. This...
Dear nrf team,
We are facing an issue with the eSIM on our nRF9151 board. The SIM 1.8V pin on the nRF9151 is not supplying 1.8V. We have checked this using a multimeter...
When trying to flash the NRF Bootloader via OpenOCD, i got this error from command line:
nRF52 device has a CTRL-AP dedicated to recover the device from AP lock. A high...
Hi team,
We are evaluating Amazon Sidewalk from Sidewalk SDK v1.0.1 , the hello-sidewalk sample is ported onto our in-house prototype board (nRF54L15). We’ve:
Provisioned...
