Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
Hello,
Got the MQTT_SIMPLE to work and the sensor samples from zephyr also, however, how can i mix the 2 to have the mqttsimple with some gpio and i2c sensor ? how will...
Hi
I have installed every requirement for the device. I want to know how to run the blinky example on the device. I can not find the SDK which has the example plus can I...
Hello, I'm currently developing a PS2 code to read the inputs of a mouse and transmit it over BLE, nrf_delay_us() is giving me a fatal error every time according to debug...
Hi,
I am trying to implement Generic HID that can transmit/receive data like CDC using the generic HID example source of nRF52820 SDK 17.0.2.
But I can't do both sending...
Hello everyone,
I'm a fresher of nRF52833. I'm facing a problem like this:
I want to read some information in Terminal but In my product I only have USB I/Os (D+ D-)....
Hi,
I'm trying to use the nRF91 as a Modem for an Arduino. Is there some example on how to use the AT commands of the serial_lte_modem sample to send a HTTP (or at least...
I built an application for the nrf51822 on top of SDK12.3, to which I added the buttonless DFU based on the "experimental_ble_app_buttonless_dfu" example.
As a boot loader...
Hi,
I want to increase the amount of BLE MIDI packages I am sending. Softdevice 132 nrf52832
MIDI data is sent by notifications and updates of the characteristic value...
Hi,
I want to use uart async on the nrf9160, I get the following linking errors at build time:
here is my prj.conf
If it's defined CONFIG_UART_INTERRUPT_DRIVEN...
Hello,
I have a question regarding the nRF5340 microcontroller or similar. Usually, when programming UART, I2C or SPI bare metal, one is using interrupts, register and buffers...
Hi Team,
We are working on project where we are trying to encrypt the advertisement data (non-connectable) using our own defined keys.
currently I have been through the...
Using Segger with PCA10056 as a debugger connected to a pcb with a NRF52840 on it. Been working fine and I tried building open bootloader and programmed it. I see the device...
Hello,
I am a newby to the nRF5340 and Zephyr and I am stuck. I would like to know how to map physical pins to a particular UARTE.
I have read in the user manual OPS_v0...
Hello,
Currently developing a system based around the NRF9160 running Zephyr. My application is threaded and i would like to run the thread_analyzer. I got this working...
