Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hi, I am developing using nrf52832 and st7735s.
Successfully displayed the lcd screen using the code in \examples\peripheral\gfx
However, when screen clear, text_8print...
Dear friend I checked the data sheet of 52820 and I didn't see any LPCOMP peripherals. Check the data sheet of 52832, there are LPCOMP peripherals. Comparing COMP and LPCOMP...
Hi,
I am working on internal flash nRF52832 merged with twi sensor, my sensor function will return a string . How to assign the string to the my_data.p_data . i am getting...
hi,
In my application, which was based on nRF_SDK_Thread, to check my node's connection with the Border router, or to know whether the border router is present or not...
Does the on-state current consumption I. E. 1.9 mA remains the same while taking different readings? Ideally, it should come the same while taking different readings. But...
Hi,
I need to upgrade the bootloader i.e mcuboot . so I decided to use primary immutable bootloader and secondary upgradable bootloader as per below link https://developer...
Hello,
I use SDK16 and softdevice S140. I want to use UART to upgrade firmware. Do you have sample code for SDK16? Do I need to install python and nrfutil on my computer...
Hello
I have managed to get two NRF5340DK linked and measured their throughput. Now I need to change their Output Radio Amplifier Power to -3dBm and test again. I use the...
Hi,
I develop a python software that flash 2 nRF chip (nRF52840 & nRF9160) with pynrfjprog (version 10.15.2). All the dll are wrapped into the generated exe and the jlink_arm_nrf_worker...
Environment
Platform: Windows 7
IDE: SEGGER Embedded Studio for ARM V5.42a (64bit)
SDK: clean nRF5_SDK_17.1.0
Project: usbd_ble_uart_c_v4 and modify with usbd function...
Hi All,
I have implemented sleep mode in the firmware. I am using NRF52833 in my project. When the device is in idle state it goes in sleep mode. Now I wanted to wakeup...
Hello,
SDK17.2, nRF52840, Keil5, SIP cannect to a OLED,
now, i want to OLED show text "DFUing" in the bootloader,
when no app, bootloader can show text in OLED, but...
Hi Sir/Miss,
I'm using nrf52832, softdevice s132 and SDK 17.0.2.
In specification, I saw nrf52832 has a ultra low power mode.
It's in system on with full retention RAM...
Hello Devs,
My device is passing through a certification process and shows up a question, which is the maximum altitude for nrf52810 for functionality. If exist any maximum...
hi, i am using nrf5340 custom board, i m trying to recieve data through uart in nrf5340 custom board from some other board.
i have defined separate pin numbers for rx and...
Hi,
I am starting to play with the nRF9160 as a modem with an external MCU and I can see that the CMUX multiplexer (GSM 07.10) is not supported by the internal modem....
I set static passkey to "123456" and enter "123456" in nRF Connect passkey request dialog. But sd_ble_gap_sec_params_reply() return 0x8 error code.
static void ble_evt_handler...
