Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hi
When l was using the function ble nus_c_string_send0 for datatransmission, an error occurred. The error code was 0x00000008.And at this point, the system resets.l don...
name:
Code:
Log1：
When the storage capacity is 64 entries, continuously reading 32 of them takes about 2 seconds.
After changing the path, run the write and...
Hi,Team,
I am developing Pawr using nrf54l15-dk.
For the Pawr example I refer to E:\NCS\v2.8.0\zephyr\samples\bluetooth\periodic_adv_rsp and periodic_sync_rsp.
I need...
I cloned a project( https://github.com/pstrueb/hci_uart ) from GitHub and added conf files to the project. How do I know that these conf files were compiled correctly?
Hi : Here is the initialization in C:
#define SPIS_INST_IDX 22
static nrfx_spis_t spis_inst = NRFX_SPIS_INSTANCE ( SPIS_INST_IDX );
void device_spis_init...
Hi,
I keep running into an error with the following output when building the configuration for nRF52840. I thought my prj.conf would fix the issue, however, the error still...
This isn't really a problem, just wanted to bring it up in case it is helpful. I'm using the nRF Connect for VS Code Extension with nRF Connect SDK v3.0.2. I have a nRF 52...
I have upgrade to nRF Connect for Desktop v5.2.0
Under the Desktop, I also upgrade Programmer APP to v4.6.2
and JLink to v818. Added the installation folder at the top...
Sometimes is interesting to see more details of each layer.
I remembered some times ago, that SoftwareDefinedRadio (SDR) comes with a lot of possibilities at a very low...
I have a custom board with nrf52832 and LIS2DW12. I was trying to poll accelerometer data, but getting "app: fetch failed: -134" error" My dts file is:
&i2c1 {
compatible...
Hi,I am working with W25Q32JW flash using nrf54l15.I saw that at present there is no support for qspi we need to try with sQspi but right i just want to check with spi communication...
Hello everyone,
I have built a few models on the nRF5340 DK, possibly more than two, and I want to run them on the board. I followed this tutorial: Run Multiple Impulses...
ticket link I have reviewed an existing thread and learned that when using Main Mode 1 or 3, the Channel Sounding Security Level is set to Level 2. For other modes, it defaults...
I am writing a custom BLE profile library and when I add new characteristics that are read write parameters and initialize the value with 0 the code seems to lose context...
