Hello Team,
Could you please share some sample application or procedure to handle power modes (Sleep, Deep Sleep, etc) of the nrf9160.
Please let me know.
Regards, ...
Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
I just downloaded the latest version of nRF Command Line Tools: nrf-command-line-tools-10.24.2-x64.exe
My desktop is running Windows 10. The installation is successful....
Can you supply Ubuntu docker image to me to build matter project(ex: bulb)?
Pay attention to my Ubuntu server is offline, so it need to whole docker image, all I need to...
Hi,
I'm porting an application from nRF5 SDK (v16.0.0) to nRF Connect SDK (v2.9.0) to be able to work with the nRF54L15. While porting our ADC functionality, I noticed that...
I am working to convert from Thingy 91 to Thingy 91x. I have successfully used the modem_shell with RTT output and control and the overlay does not seem to work with SDK 2...
I'm having a lot of new trouble posting to devzone. I can not drag/drop files. It keeps suggesting "An error occurred. Please try again or contact your administrator." This...
Hello,
I have to handle two devices with one UART. Previously, I made it by suspending UART, changing its state between PINCTRL_STATE_DEFAULT and PINCTRL_STATE_SLEEP and...
I am using the nRF9160 to upload a large set of data in chunk of 16kB in MQTT datamode. I am using the v2.6.1 SDK and toolchain. During the MQTT upload the connection seems...
I'm migrating my app from parent/child to sysbuild.
Previously I had both bootloader and firmware as separate out-of-tree projects and that was working fine.
Now using...
I am trying to define a simple output pin.
in the DTS file I have:
aliases {
ledred = &hwledred;
ledgreen = &hwledgreen;
memwp = &hwmemwp;
};
soc {
gpio0...
I'm implementing an OAUTH procedure on my device. I'm able to access login.microsoftonline.com and get user and device codes, then after authorizing, I can access the token...
LE audio demo,i enable CONFIG_STREAM_BIDIRECTIONAL ,when i connected Galaxy Buds3 by cis.
my uart_tx will stop.cpu looks busy.when disconnect with headset.data will...
Hello, I have a problem trying to connect Direct Test Mode desktop app to my custom board running Zephyr on nRF52833. My firmware sample is based on hci_uart https://github...
Hi folks,
I've been trying to use the sw_pwm to generate two PWM outputs. I'm using sw_pwm because I want to achieve lower frequencies (1-100Hz) and the hardware PWM API...
Hello,
I need to connect the Thingy:91 to an MCU via UART and/or SPI bus. I need help to identify the pins for communications for:
SPI: CSK, CS, MISO, and MOSI
UART...
Hi, I am new to working on the display . I am trying to integrate nrf5340dk board with waveshare lcd module which is of 1.14 inch and has st7789v controller by using SPI communication...
