Hi,
I'm starting to implement DFU using IAR's ARM workbench. In the example project for ARM that comes with the nrf51_sdk_v5_2_0_39364 SDK there is a file called bootloader_util_arm...
Do I have to use external host MCU for nRF51422? What can the ARM Cortex processor inside SoC 51422 do and cannot do?
I want to create a mesh network with hundreds of ANT...
Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
Hi,
I use the nrf51422 chip.I want to know if the ANT establish link between chips,where can I get the matching configuration (like device type、channel ID).I mean is...
Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
I am creating a custom board with an W25Q128JVPIQTR external flash drive using SPI with a nrf5340. The pins are:
P0.08 - SD_CLK
P0.09 - SD_MOSI
P0.10 - SD_MISO ...
Regarding the operation of EJ2832AA1 (nRF52832), Please answer the following questions. nRF5 SDK ： v15.3.0 SoftDevice ： S132 v6.1.1
I am doing UART communication with another...
Hello, I am new here and I hope to not duplicate any other similar post (to be honest I have search a lot before writing). I am working with nrf52840DK, I have used blinky...
Hi,
Is there anyway to start after stopping the PWM with a PPI channel?
There is a start task in the PWM, but
But not defined in the nrfx pwm driver (nrf_pwm.h)
I...
We're trying to set up MQTT messaging between our custom nRF9160 device and our private AWS VPC. When using the Serial Terminal in nRF Connect for Desktop to monitor the device...
I am reaching out to request assistance regarding a FOTA (Firmware Over-The-Air) operation using the HTTPS protocol for my new nRF7002-DK development kit. I have successfully...
Hi, we're creating a BLE mouse. We've setup the HID service- clicking button 1 on the nrf52832DK sends left mouse button click- nothing else is being sent. The problem: even...
Hi
I heard about that RSSI has no relationship with disconnection. However, based on my experiments, the connection will break every time I am close to -80dBm.
I am confused...
Does anyone know of a good starting point for Bosch BHI360 IMU integration into nrf5340 and Zephyr?
Did look at: https://community.bosch-sensortec.com/mems-sensors-forum...
Hi,nrf52832 entered in bootloader mode.as ld5 led is keep blinking on power reset and holding if boot/reset button.please help me to get board back to normal mode.thanks.
I had previously gotten working code to communicate with my SPI device on the nRF5340DK w/ NCS v2.5.0 that uses the HAL SPI library inside TF-M. I used NCS v2.5.0 (nrf\samples...
I observed another user having this same issue with resolution.
It appears the watchdog configuration has changed but I'm unable to track down the driver/overlay/etc that...
Hello,
I am working on an nRF5340-based project where I successfully integrated the broadcast_source and central_and_peripheral_hr examples from SDK 2.6.0. Both functionalities...
Hello,
Sorry for the many tickets the past few days, but I am ramping up to start a nRF Connect SDK project on a nRF91 modem and have encountered some initial growing pains...
Hello all,
I'm working on a localization system using the nRF52832 chip and Bluetooth Low Energy (BLE), but I'm running into challenges due to how BLE transmits signals...
