Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
We are evaluating Segger SystemView for analyzing our embedded applications. However, we encountered occasional overflows in SystemView. These overflows are caused by...
Hello
how can i found a input capture example to read external 125KHz PWM Signal, so we can measure the time from falling/falling edge or rising/rising edge or falling/rising...
Hello, from reading devzone, the recommendation for optimal GPS performance while using the nRF9160 DK, is for the antenna to have an unobstructed view of the open sky.
...
Hello,
We have got some devices in the field that run mfw1.3.1 and an application that have some issues with preforming modem FOTA correctly. I'd like to update them to...
Hello,
I have been trying to provision and configure two nodes running Light and the Light_switch examples using a separate node running the mesh provisioner example from...
Hi,
I'm porting an older product that used a Microchip MRF24J40 SPI radio and a PIC processor to an nRF52840 and I'm struggling with how to replicate both the CRC calculations...
Hello,
I am using nRF Connect for VSCode (v2022.7.242) and discovered that the softreset option for a task has no effect.
Task:
Output:
As you can see it is...
Hi All!
I am using a hologram NB-IoT sim card in nrf9160DK. And want to connect it /send data to nrf cloud. I have activated the sim from the hologram website. When I tried...
I bought this device becouse I want to use it as Open Thread Border Router.
I followed the steps on your website: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
Hi All:
Good night!
We have 3 pcs of nrf52840-DK and would like to implement and test remote provision functionality with nrfsdk_17.0.2 and nrfsdk_mesh_5.0.
When compiling...
Hi，i'm use latest ncs sdk to develop bluetooth application which use Periodic advertising, when i get started with samples(bluetooth/periodic_adv), and use Ellisys capture...
Hello,
Is AT+COPS manual selection mandatory or just a preference? We have an issue with 9160 choosing a network without PSM if it has better signal quality (when roaming...
Trying to flash devices and getting this error:
make flash
DONE nrf52840_xxaa Flashing: _build/nrf52840_xxaa.hex nrfjprog -f nrf52 --program _build/nrf52840_xxaa.hex ...
Hi,
In our old project we developed low energy sensors based on the Nrf52811 (nrf Connect sdk), using advertisements to broadcast the sensor data, then collecting them with...
