I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
P19 (Debug OUT Connector) on the nRF52840 BLE RF Development Board, PCA10056 (Dev Board) provides the ability to program a nRF52840 BLE board (BLE Board).
Questions:
...
Hi there,
Attempting to use the sample program for direction finding and have been following Case ID: 280319. Have attempted to add the code suggested by Simonr in adding...
Hi,
I'm working on a project using Zephyr and ncs 1.7.1. One of its functions is to stream WAV files from a SD card. It only ever reads data.
The issue I'm having is...
Hi all,
I am using SES in Win10. After I updated my NCS to 1.7.1, I failed to open my solution. However, it runs succussfully in SDK 1.6.1. The infomation is below:
...
Hello.
I am currently working on implementing a PWM control function using nrf52840. I used the function "es_battery_voltage_get()" to read the battery voltage before and...
I have written simple hello world code on nRF9160 custom board and enables the MCUBoot as bootloader using CONFIG_BOOTLOADER_MCUBOOT=y in prj.conf file.
Also, made some...
Hi everyone, I'm trying to communicate with OBDII through NUS using nRF52832. I was able to initiate the connection, send commands to OBDII, and get responses on the ECUsim...
The current RRC Inactivity Timer from my provider is 10 seconds, causing my power consumption in RRC Connected mode to be unnecessarily high.
I want to use the Release Assistance...
Hi,
Can anyone check if my understanding about this NFC-BLE pairing feature is correct?
1.Before connecting, two BLE devices will exchange some keys or info for secure...
Hello,
I'm working on an application that will use the nrf9160/nrf52. I will need to make https REST calls where I will populate the http header with username/password credentials...
I didn't manage to find a solution to my problem here but I fixed it myself so I'm posting it just in case it helps someone else.
I installed JLink 5.12.6 and nRF5x Command...
Hi,
Android shows a message that the NFC Pairing was not successful, but it looks that the connection was established successfully (Device in the connected devices, data...
Hi All,
I have a measuring device that needs to send UART data over BLE to a PC with BLE dongle or Macbook with built in BLE. My test users need to open up a webpage in...
Okay, I've run into an interesting scenario.
SDK 17.0.2
NRF 52840 (DK)
I am coding a multiperipharal service on a multiperipheral ble device.
My attempt at updating...
